Linksys wrt54g3g - router UMTS [NEW]

Pozostałe zagadnienia (sprzętowe i programowe), które nie pasują do powyższych kategorii np. optymalizacja łącza, liczniki danych, bezpieczeństwo w sieci, informacje podstawowe.

Moderator: Moderatorzy

trademark
Początkujący użytkownik forum
Posty: 12
Rejestracja: 2009-08-14, 10:26
Lokalizacja: Łomianki

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: trademark »

Źle napisałem :) Nie chodziło mi, że jest połączenie, tylko o to, że w ogóle się uruchamia i migają lampki, ale nadal się nie łączy, bo nie wiem jak to skonfigurować wszystko. Nie mogę znaleźć go w tych logach - tego co jest na stronie, którą podałeś.
Awatar użytkownika
Patryk
Guru bezprzewodowy
Posty: 6692
Rejestracja: 2007-09-12, 21:16
Lokalizacja: Z dziczy

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: Patryk »

Pokaż wynik wykonania poleceń logread i dmesg, oraz cat /proc/bus/usb/devices
trademark
Początkujący użytkownik forum
Posty: 12
Rejestracja: 2009-08-14, 10:26
Lokalizacja: Łomianki

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: trademark »

Ehh, dopiero teraz mam czas się za to zabrać :)

No więc tak. Odkryłem jeszcze jeden problem, mianowicie po resecie routera blokuje mi się możliwość zmiany plików. Pomaga dopiero polecenie:

mtd unlock rootfs_data

Pół biedy, gdyby nie przeszkadzało to w normalnym użytkowaniu, tylko musiałbym tego używać do instalacji i zmian w konfiguracji, ale powoduje to również, niestety, konieczność każdorazowego przeinstalowywania pakietu kmod-pcmcia-core. Jeśli nie odinstaluję tego pakietu, potem nie wydam w/w polecenia, a następnie nie zainstaluję ponownie kmod-pcmcia-core, to router wydaje mi się, że nie wczytuje driverów dla pcmcia. Jak robię cardctl status zaraz po resecie (bez tej zabawy w reinstalację) to pisze:

no pcmcia driver in /proc/devices


Dobra, a teraz odnośnie logów samego modemu:

logread:

Kod: Zaznacz cały

Apr  6 02:18:00 OpenWrt syslog.info syslogd started: BusyBox v1.15.3
Apr  6 02:18:00 OpenWrt user.notice kernel: klogd started: BusyBox v1.15.3 (2010-04-06 04:14:37 CEST)
Apr  6 02:18:00 OpenWrt user.warn kernel: CPU revision is: 00029007
Apr  6 02:18:00 OpenWrt user.warn kernel: Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Apr  6 02:18:00 OpenWrt user.warn kernel: Primary data cache 4kB, 2-way, linesize 16 bytes.
Apr  6 02:18:00 OpenWrt user.warn kernel: Linux version 2.4.37.9 ([email protected]) (gcc version 3.4.6 (OpenWrt-2.0)) #42 Tue Apr 6 15:59:04 CEST 2010
Apr  6 02:18:00 OpenWrt user.warn kernel: Determined physical RAM map:
Apr  6 02:18:00 OpenWrt user.warn kernel:  memory: 01000000 @ 00000000 (usable)
Apr  6 02:18:00 OpenWrt user.warn kernel: On node 0 totalpages: 4096
Apr  6 02:18:00 OpenWrt user.warn kernel: zone(0): 4096 pages.
Apr  6 02:18:00 OpenWrt user.warn kernel: zone(1): 0 pages.
Apr  6 02:18:00 OpenWrt user.warn kernel: zone(2): 0 pages.
Apr  6 02:18:00 OpenWrt user.warn kernel: Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
Apr  6 02:18:00 OpenWrt user.warn kernel: CPU: BCM4712 rev 1 at 200 MHz
Apr  6 02:18:00 OpenWrt user.warn kernel: Using 100.000 MHz high precision timer.
Apr  6 02:18:00 OpenWrt user.warn kernel: Calibrating delay loop... 197.83 BogoMIPS
Apr  6 02:18:00 OpenWrt user.info kernel: Memory: 14240k/16384k available (1447k kernel code, 2144k reserved, 100k data, 84k init, 0k highmem)
Apr  6 02:18:00 OpenWrt user.info kernel: Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Apr  6 02:18:00 OpenWrt user.info kernel: Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Apr  6 02:18:00 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Apr  6 02:18:01 OpenWrt user.info kernel: roboswitch: Probing device eth0: found a 5325! It's a 5350.
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Apr  6 02:18:01 OpenWrt user.info kernel: mini_fo: using base directory: /
Apr  6 02:18:01 OpenWrt user.info kernel: mini_fo: using storage directory: /overlay
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Apr  6 02:18:01 OpenWrt user.warn kernel: Erase at 0x00040000 failed immediately: -EROFS. Is the sector locked?
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Apr  6 02:18:01 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Apr  6 02:18:01 OpenWrt user.warn kernel: Erase at 0x00050000 failed immediately: -EROFS. Is the sector locked?
Apr  6 02:18:01 OpenWrt user.warn kernel: jffs2.bbc: SIZE compression mode activated.
Apr  6 02:18:03 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Apr  6 02:18:03 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Apr  6 02:18:04 OpenWrt user.info kernel: usb.c: registered new driver usbdevfs
Apr  6 02:18:04 OpenWrt user.info kernel: usb.c: registered new driver hub
Apr  6 02:18:05 OpenWrt user.info kernel: Linux Kernel Card Services 3.1.22
Apr  6 02:18:05 OpenWrt user.info kernel:   options:  [pci] [cardbus]
Apr  6 02:18:05 OpenWrt user.debug kernel: eth0.0: add 01:00:5e:00:00:01 mcast address to master interface
Apr  6 02:18:06 OpenWrt user.notice kernel: ds: no socket drivers loaded!
Apr  6 02:18:06 OpenWrt user.warn kernel: PCI: Enabling device 01:01.0 (0000 -> 0002)
Apr  6 02:18:06 OpenWrt user.info kernel: Yenta ISA IRQ mask 0x06f8, PCI irq 2
Apr  6 02:18:06 OpenWrt user.info kernel: Socket status: 30000820
Apr  6 02:18:06 OpenWrt user.info kernel: eth0.0: dev_set_promiscuity(master, 1)
Apr  6 02:18:06 OpenWrt user.info kernel: device eth0 entered promiscuous mode
Apr  6 02:18:06 OpenWrt user.info kernel: device eth0.0 entered promiscuous mode
Apr  6 02:18:06 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering learning state
Apr  6 02:18:06 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering forwarding state
Apr  6 02:18:06 OpenWrt user.info kernel: br-lan: topology change detected, propagating
Apr  6 02:18:07 OpenWrt user.debug kernel: eth0.1: add 01:00:5e:00:00:01 mcast address to master interface
Apr  6 02:18:10 OpenWrt user.debug kernel: PCI: Setting latency timer of device 00:01.0 to 64
Apr  6 02:18:10 OpenWrt user.emerg kernel: PCI/DMA
Apr  6 02:18:10 OpenWrt user.emerg kernel: wl0: wlc_attach: chiprev 1 coreunit 0 corerev 7 cccap 0x4876a maccap 0x0 band 2.4G, phy_type 2 phy_rev 2 ana_rev 2
Apr  6 02:18:10 OpenWrt user.warn kernel: wl0: Broadcom BCM4320 802.11 Wireless Controller 4.150.10.5
Apr  6 02:18:10 OpenWrt user.info sysinit: Warning: loading wl will taint the kernel: non-GPL license - Proprietary
Apr  6 02:18:10 OpenWrt user.info sysinit:   See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Apr  6 02:18:10 OpenWrt user.info kernel: CSLIP: code copyright 1989 Regents of the University of California
Apr  6 02:18:11 OpenWrt user.info kernel: PPP generic driver version 2.4.2
Apr  6 02:18:12 OpenWrt user.warn kernel: ip_tables: (C) 2000-2002 Netfilter core team
Apr  6 02:18:14 OpenWrt user.warn kernel: ip_conntrack version 2.1 (5953 buckets, 5953 max) - 352 bytes per conntrack
Apr  6 02:18:16 OpenWrt user.info kernel: usb-uhci.c: $Revision: 1.275 $ time 09:17:22 Apr  1 2010
Apr  6 02:18:16 OpenWrt user.info kernel: usb-uhci.c: High bandwidth mode enabled
Apr  6 02:18:16 OpenWrt user.debug kernel: PCI: Setting latency timer of device 00:03.0 to 64
Apr  6 02:18:16 OpenWrt user.info kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Apr  6 02:18:17 OpenWrt user.info kernel: usb.c: registered new driver serial
Apr  6 02:18:17 OpenWrt user.info kernel: usbserial.c: USB Serial support registered for Generic
Apr  6 02:18:17 OpenWrt user.info kernel: usbserial.c: USB Serial Driver core v1.4
Apr  6 02:18:20 OpenWrt user.info kernel: device wl0 entered promiscuous mode
Apr  6 02:18:20 OpenWrt user.info kernel: br-lan: port 2(wl0) entering learning state
Apr  6 02:18:20 OpenWrt user.info kernel: br-lan: port 2(wl0) entering forwarding state
Apr  6 02:18:20 OpenWrt user.info kernel: br-lan: topology change detected, propagating
Apr  6 02:18:21 OpenWrt user.info sysinit: Loading defaults
Apr  6 02:18:22 OpenWrt user.info sysinit: Loading synflood protection
Apr  6 02:18:22 OpenWrt user.info sysinit: Adding custom chains
Apr  6 02:18:23 OpenWrt user.info sysinit: Loading zones
Apr  6 02:18:24 OpenWrt user.info sysinit: Loading forwarding
Apr  6 02:18:25 OpenWrt user.info sysinit: Loading redirects
Apr  6 02:18:25 OpenWrt user.info sysinit: Loading rules
Apr  6 02:18:25 OpenWrt user.info sysinit: Loading includes
Apr  6 02:18:25 OpenWrt user.info sysinit: Loading zone defaults
Apr  6 02:18:26 OpenWrt user.notice root: adding lan (br-lan) to firewall zone lan
Apr  6 02:18:27 OpenWrt user.notice rdate: Failed to sync with ac-ntp0.net.cmu.edu
Jul 10 08:59:34 OpenWrt user.notice rdate: Synced with ptbtime1.ptb.de
Jul 10 08:59:34 OpenWrt authpriv.info dropbear[672]: Running in background
Jul 10 08:59:34 OpenWrt user.info sysinit: WARNING: the specified certificate and key files do not exist and the px5g generator is not available, skipping SSL setup.
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: started, version 2.52 cachesize 150
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: using local addresses only for domain lan
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: reading /tmp/resolv.conf.auto
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: using nameserver 192.168.1.1#53
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: using local addresses only for domain lan
Jul 10 08:59:36 OpenWrt daemon.info dnsmasq[693]: read /etc/hosts - 1 addresses
Jul 10 09:04:27 OpenWrt authpriv.info dropbear[701]: Child connection from 192.168.1.8:1182
Jul 10 09:04:32 OpenWrt authpriv.notice dropbear[701]: password auth succeeded for 'root' from 192.168.1.8:1182
i dmesg:

Kod: Zaznacz cały


CPU revision is: 00029007
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 4kB, 2-way, linesize 16 bytes.
Linux version 2.4.37.9 ([email protected]) (gcc version 3.4.6 (OpenWrt-2.0)) #42 Tue Apr 6 15:59:04 CEST 2010
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
CPU: BCM4712 rev 1 at 200 MHz
Using 100.000 MHz high precision timer.
Calibrating delay loop... 197.83 BogoMIPS
Memory: 14240k/16384k available (1447k kernel code, 2144k reserved, 100k data, 84k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
b44.c:v0.93 (Mar, 2004)
PCI: Setting latency timer of device 00:02.0 to 64
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:18:39:ee:06:5a
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
cfi_cmdset_0001: Erase suspend on write enabled
0: offset=0x0,size=0x2000,blocks=8
1: offset=0x10000,size=0x10000,blocks=63
Using word write method
Flash device: 0x400000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x1a68f2
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x000bc000-0x00270000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x00270000-0x003f0000 : "rootfs_data"
sflash: found no supported devices
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 84k freed
diag: Detected 'Linksys WRT54G3G'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Erase at 0x00040000 failed immediately: -EROFS. Is the sector locked?
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Erase at 0x00050000 failed immediately: -EROFS. Is the sector locked?
jffs2.bbc: SIZE compression mode activated.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus]
eth0.0: add 01:00:5e:00:00:01 mcast address to master interface
ds: no socket drivers loaded!
PCI: Enabling device 01:01.0 (0000 -> 0002)
Yenta ISA IRQ mask 0x06f8, PCI irq 2
Socket status: 30000820
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device eth0.0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: port 1(eth0.0) entering forwarding state
br-lan: topology change detected, propagating
eth0.1: add 01:00:5e:00:00:01 mcast address to master interface
PCI: Setting latency timer of device 00:01.0 to 64
PCI/DMA
wl0: wlc_attach: chiprev 1 coreunit 0 corerev 7 cccap 0x4876a maccap 0x0 band 2.4G, phy_type 2 phy_rev 2 ana_rev 2
wl0: Broadcom BCM4320 802.11 Wireless Controller 4.150.10.5
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 352 bytes per conntrack
usb-uhci.c: $Revision: 1.275 $ time 09:17:22 Apr  1 2010
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:03.0 to 64
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
device wl0 entered promiscuous mode
br-lan: port 2(wl0) entering learning state
br-lan: port 2(wl0) entering forwarding state
br-lan: topology change detected, propagating
Uff, dużo tego.
Dzięki za pomoc z góry :)

BTW. tego katalogu co podałeś w ogóle u mnie nie ma.

[ Dodano: 2010-07-10, 22:06 ]
Zainstalowałem kamikaze i tutaj nie mam problemu z blokowaniem się plików. Tutaj mam /proc/bus/usb/devices ale jest pusty.
Awatar użytkownika
COVERek
Stały użytkownik forum
Posty: 93
Rejestracja: 2008-07-10, 20:23
Lokalizacja: Łódź

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: COVERek »

Mam bardzo podobny problem tylko ze z modemem GE0301 i routerem wrt54g3g.
Po zainstalowaniu najnowszego OpenWrt nie swieca sie diody na modemie, podobnie jest na X-Wrt.
Mialem chwilowo zainstalowane jakies stare x-wrt i diody sie swiecily ale sie nie laczyl.
Co zdrobic zeby zapalily se te diody na modemie?! Wnioskuje, ze nie idzie napiecie do modemy czy cos...

---

Sprawdzałem na sofcie dla brcm47xx i na brcm2-4...

Instalowałem pakiety:
pcmcia-cs kmod-pcmcia-core kmod-usb-serial-option kmod-usb-ohci kmod-usb-uhci kmod-usb-serial

Diody na modemie za Chiny nie chcą się zapalić, a co za tym idzie modem nie jest wykryty... Już nie mam pomysłów na ten złom....


----

Trzeci dzień i nic...
Na modemie swieca sie ledy tylko po zainstalowaniu z obrazu: 8_openwrt-3g-r75-wrt54g3g-squashfs.bin

Sprzęt który chce pogodzić to: WRT54G3G v1.1 + Option GE0301 (express card) + przejściówka PCMCIA.

Jakieś konkretne rady....
:klnie:
Linux User #462372 || Ubuntu User #20118
trademark
Początkujący użytkownik forum
Posty: 12
Rejestracja: 2009-08-14, 10:26
Lokalizacja: Łomianki

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: trademark »

Napisałem Ci w PW, że niezbędnym pakietem okazał się, w moim przypadku, PCMCIA-CS. Na pewno jest na Kamikaze z kernelem 2.4. Z tego co pamiętam na Backfire też jest, ale niestety u mnie nie działa jak należy ten soft i po restarcie routera muszę wszystko instalować od nowa, tak więc wróciłem do starszego.

Tu masz listę pakietów, które mam zainstalowane:
-pcmcia-cs
-kmod-pcmcia-core (w Backfire jeszcze kmod-pcmcia-yenta będziesz potrzebował)
-comgt
-kmod-usb-serial
-kmod-usb-core
-kmod-usb-ohci

Jak zainstalujesz je to podłącz modem. Jeśli zaświecą się lampki to pokaż wyniki logread.
1.Merlin XU870 + WRT54G3G-V2 (OFW) + iPlus
2.Option 3G + WRT54G3G (OpenWRT tests)
3.WRT54GL (DD-WRT)
Awatar użytkownika
COVERek
Stały użytkownik forum
Posty: 93
Rejestracja: 2008-07-10, 20:23
Lokalizacja: Łódź

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: COVERek »

Znalazlem tutorial:
https://forum.openwrt.org/viewtopic.php?id=20063
Robilem wedlug niego, ale nie wybieral mi polaczenia po ifup, byl za to komunikat:
timeout checking for PIN.wwan(3g): Failed to set the PIN code.
a w logread nastepujaca informacja...
Jul 14 14:48:59 OpenWrt user.err kernel: hub.c: Maybe the USB cable is bad?
Linux User #462372 || Ubuntu User #20118
trademark
Początkujący użytkownik forum
Posty: 12
Rejestracja: 2009-08-14, 10:26
Lokalizacja: Łomianki

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: trademark »

Zainstalowałeś wszystkie pakiety które Ci podałem? Zapodaj cały logread a nie tylko jeden wycinek.
1.Merlin XU870 + WRT54G3G-V2 (OFW) + iPlus
2.Option 3G + WRT54G3G (OpenWRT tests)
3.WRT54GL (DD-WRT)
Awatar użytkownika
COVERek
Stały użytkownik forum
Posty: 93
Rejestracja: 2008-07-10, 20:23
Lokalizacja: Łódź

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: COVERek »

Udalo sie uruchomic net na Trunku openwrt. Niestety polaczenie ttyUSB0 i ttyUSB1 nie dzialaja...
Chodzi tylko ttyUSB2... Nie moge pozyskac info na temat poleczenia, a na tym mi najbardziej zalezalo... ;/
A to bylo glownym celem konfiguracji openwrt w tym przypadku... Eh. Jak macie propozycje dlaczego, chetnie poczytam... :cry:
Linux User #462372 || Ubuntu User #20118
robekpw
Początkujący użytkownik forum
Posty: 18
Rejestracja: 2008-01-25, 18:02
Lokalizacja: Warszawa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: robekpw »

witam,
mam pytanie odnośnie modemu 3G linksysa.
Nie otwiera się link z listą obsługiwanych modemów. Czy może ktoś z Was posiada taką listę? Chodzi mi o net w orange.
Czy ktoś z Was wykorzystuje ten router do monitoringu? Chciałbym podłączyć kamerę wifi do niego.
Jaki zasięg na otwartej przestrzeni posiada? Zakładając, że router jest tylko za ścianą lub za oknem?

:)
Dzięki
mattib4
Początkujący użytkownik forum
Posty: 3
Rejestracja: 2011-01-26, 18:04
Lokalizacja: Warszawa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: mattib4 »

Witam wszystkich.
Jakiś czas temu <font color="#FF00FF"><b>»»wziąć««</b></font> z pracy ten ruterek. Na razie mam stałe łącze i chodzi jak zły jednak tylko do marca. Od marca chciałem korzystać z mojego bezprzewodowego internetu play. <font color="#FF00FF"><b>»»wziąć««</b></font> więc z pracy jeszcze modem pcimcia Option GT 3G+ EMEA ale pod Iplusa. I teraz moje pytanie. Po włożeniu karty play do modemu Iplus a później routera migają najpierw dwie lampki czerwona i niebieska a później tylko niebieska znaczy, że modem się zalogował. Jednak ruter nie widzi modemu nic się nie świeci itd. W czym problem, że karta play nie pasuje do modemu iplus?? Ale loguję się przecież. Proszę o jakieś pomysły.??

A w ruterze jest najnowszy soft 2.11.05 był już seryjnie
Awatar użytkownika
krystianb
Guru bezprzewodowy
Posty: 10350
Rejestracja: 2008-03-19, 17:10
Lokalizacja: wa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: krystianb »

mattib4 pisze: Ale loguję się przecież. Proszę o jakieś pomysły.??
Modemy optiona logują się do sieci nawet tylko z podłączonym zasilaniem. Jest małe prawdopodobieństwo, że router nie rozpoznaje modemu z plusa, choć to trochę dziwne bo modem działa na standardowych sterownikach optiona.

Masz w modemie firmware przynajmniej 3.15 ??
Za prośbę pomocy na gg/pw gwarantuje czerwony prezent!
mattib4
Początkujący użytkownik forum
Posty: 3
Rejestracja: 2011-01-26, 18:04
Lokalizacja: Warszawa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: mattib4 »

Jaki firmware to nie wiem. Nie mam jak tego sprawdzić bo w netbooku nie mam pcimci. Problem jednak rozwiązał się inaczej bo <font color="#FF00FF"><b>»»wziąć««</b></font> też modem hauwei e630 też z iplusa. Na nim z kolei chodzi jak głupi :) Jak wsadziłem płytę linksysa do konfiguracji to przy optionie napisał mi że modem is not supported a na huawei poszedł. W sumie troszkę szkoda bo option jest chyba troszkę lepszy czyż nie??
Awatar użytkownika
krystianb
Guru bezprzewodowy
Posty: 10350
Rejestracja: 2008-03-19, 17:10
Lokalizacja: wa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: krystianb »

mattib4 pisze:option jest chyba troszkę lepszy czyż nie??
E630 ma 7.2 Mb (ewentualnie 3.6 jak go nikt wcześniej nie upgradował) Przy dobrym sygnale lepiej będzie się sprawował, nawet przy ograniczeniu do 1Mb, lepiej wykorzysta przydzielone zasoby.
Za prośbę pomocy na gg/pw gwarantuje czerwony prezent!
mattib4
Początkujący użytkownik forum
Posty: 3
Rejestracja: 2011-01-26, 18:04
Lokalizacja: Warszawa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: mattib4 »

O No to super jak znajdę jakiegoś laptopa z pcimcia to zrobię mu uprgrade. Najnowszy firmware na stronie huawei?
Awatar użytkownika
krystianb
Guru bezprzewodowy
Posty: 10350
Rejestracja: 2008-03-19, 17:10
Lokalizacja: wa

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: krystianb »

Najlepiej bez kombinowania wrzucić firmware ze strony iplusa, do innych prawdopodobnie będzie potrzebny kod, który co prawda można wygenerować, ale ten ze strony plusa powinien wystarczyć.

Aha część modemów już fabrycznie była 7.2Mb/s
Za prośbę pomocy na gg/pw gwarantuje czerwony prezent!
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Problem z wgraniem softu

Post autor: aramisrobi »

Proszę o pomoc w wgraniu softu a minowicie
1 podłączam komputer z routerem przez 1 – 4 portów LAN , wchodzę w zakładkę /Administration/Firmware Upgrade i wybieram plik z nowym softem , znalazłem dwa pierwszy openwrt-r51-wrt54g3g-st-squashfs.bin 1941 kb , drugi openwrt-wrt54g3g-squashfs.bin 1385 kb . Wybieram ten pierwszy bo grubszy :) na razie wszystko idzie ok. Pasek przesuwa się przy wgrywaniu upgreatu po dojści do połowy zatrzymuje się i wraca do początku i to wszystko mam nadal stary soft.
Co jest nie tak ?
moher
Specjalista bezprzewodowy-senior
Posty: 379
Rejestracja: 2011-02-02, 15:43
Lokalizacja: Szczecin

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: moher »

Skąd masz te obrazy?

Nalepie ściągnąć ze strony OpenWrt:

http://downloads.openwrt.org/backfire/1 ... /brcm47xx/
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

moher pisze:Skąd masz te obrazy?

Nalepie ściągnąć ze strony OpenWrt:

http://downloads.openwrt.org/backfire/1 ... /brcm47xx/

Dzięki
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

Mam prośbę o orginalny soft wrt54g3g eu/em driver . Wszystkie znalezione linki w gogle nie działają
Awatar użytkownika
Jo_gurt
Guru bezprzewodowy
Posty: 16330
Rejestracja: 2007-11-16, 21:49
Lokalizacja: Lublin

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: Jo_gurt »

Kto by pomyślał, że na stronie producenta :P
http://homedownloads.cisco.com/download ... I_code.bin (v 1.1)
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

Jo_gurt pisze:Kto by pomyślał, że na stronie producenta :P
http://homedownloads.cisco.com/download ... I_code.bin (v 1.1)
Dzięki stary ale zawsze mnie przekierowuje na

http://home.cisco.com/pl-eu/home :gwiazdki:
Awatar użytkownika
wojteks
*** Administrator ***
Posty: 26111
Rejestracja: 2007-12-02, 11:51
Lokalizacja: PL

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: wojteks »

aramisrobi pisze: ale zawsze mnie przekierowuje na
Pierwsze kliknięcie "otwórz w nowym oknie" i dostaję opcję zapisu na dysk, testowane w FF.
Zmień przeglądarkę.
Nie pomagam na PW!
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

Wgrałem do routera openwrt , konfiguracja mnie przerosła . Router jest sprawny łącze się telnetem i winscp . Chcę wrócić do oryginalnego softu przez www openwrt ale router nie pozwala .Moze ktoś podpowie jakim narzędziem i jak to zrobić .
key
*Mistrz bezprzewodowy*
Posty: 9565
Rejestracja: 2010-08-01, 18:30
Lokalizacja: Nürnberg

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: key »

aramisrobi pisze:Moze ktoś podpowie jakim narzędziem i jak to zrobić .
Oryginalny soft najlepiej wgrac po TFTP. Alternatywnie sprobuj wgrac Tomato - powinno pojsc z interface WWW i jest duzo prostrze w konfiguracji od OpenWRT.
Nie pomagam na PW.
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

key pisze:
aramisrobi pisze:<font color="#FF0000"><b>[...]</b></font>
Oryginalny soft najlepiej wgrac po TFTP. Alternatywnie sprobuj wgrac Tomato - powinno pojsc z interface WWW i jest duzo prostrze w konfiguracji od OpenWRT.
Można prosić o linki do progamu bo w googlach tftp jest pełno i nie wiem co wybrać , Tomato na pcimcie ???????

[ Komentarz dodany przez: YaHooo: 2011-10-24, 20:38 ]
<a href="http://www.bez-kabli.pl/viewtopic.php?p=59341#59341">Panie i Panowie tniemy cytaty!</a>
Ostatnio zmieniony 2011-10-24, 19:37 przez aramisrobi, łącznie zmieniany 1 raz.
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

Czy pomoże mi ktoś dograć pakiety ipk do rutera
przekopiowałem do tmp w konsili wpisuje
ipkg install /tmp/kmod-pcmcia_2.4.30-brcm-5_mipsel.ipk
ipkg not found

Proszę o kontakt na prv
Awatar użytkownika
Jo_gurt
Guru bezprzewodowy
Posty: 16330
Rejestracja: 2007-11-16, 21:49
Lokalizacja: Lublin

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: Jo_gurt »

aramisrobi pisze:Proszę o kontakt na prv
Po co, po to jest forum.
aramisrobi pisze:ipkg not found
A próbowałeś opkg zamiast ipkg? ipkg był używany w starych OpenWRT.
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

Using username "root".
[email protected]'s password:
Access denied
[email protected]'s password:


BusyBox v1.15.3 (2011-07-06 13:01:07 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
Backfire (10.03.1-RC5, r27608) --------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:~# opkg install /tmp/kmod-pcmcia_2.4.30-brcm-5_mipsel.ipk
Unknown package 'kmod-pcmcia'.
Collected errors:
* pkg_hash_fetch_best_installation_candidate: Packages for kmod-pcmcia found, b ut incompatible with the architectures configured
* opkg_install_cmd: Cannot install package kmod-pcmcia.
root@OpenWrt:~# opkg install /tmp/kmod-pcmcia-serial_2.4.30-brcm-5_mipsel.ipk
Unknown package 'kmod-pcmcia-serial'.
Collected errors:
* pkg_hash_fetch_best_installation_candidate: Packages for kmod-pcmcia-serial f ound, but incompatible with the architectures configured
* opkg_install_cmd: Cannot install package kmod-pcmcia-serial.
root@OpenWrt:~# opkg install /tmp/pcmcia-utils_3.2.8-1_mipsel.ipk
Unknown package 'pcmcia-utils'.
Collected errors:
* pkg_hash_fetch_best_installation_candidate: Packages for pcmcia-utils found, but incompatible with the architectures configured
* opkg_install_cmd: Cannot install package pcmcia-utils.
root@OpenWrt:~#
Coś jest nie tak , czy pakiety sa zainstalowane? Modemu nadal nie można <font color="#FF00FF"><b>»»znaleźć««</b></font>.
key
*Mistrz bezprzewodowy*
Posty: 9565
Rejestracja: 2010-08-01, 18:30
Lokalizacja: Nürnberg

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: key »

aramisrobi pisze:Coś jest nie tak , czy pakiety sa zainstalowane?
Pakiety nie sa zainstalowane:
aramisrobi pisze:opkg_install_cmd: Cannot install package....

Starasz sie instalowac pakiety z zlego zrodla:
aramisrobi pisze:Packages for kmod-pcmcia found, but incompatible with the architectures configured
Podsun odpowiednie odressy do pakietow.
Nie pomagam na PW.
aramisrobi
Początkujący użytkownik forum
Posty: 10
Rejestracja: 2010-10-20, 14:30
Lokalizacja: NA

Re: Linksys wrt54g3g - router UMTS [NEW]

Post autor: aramisrobi »

Gdzie mogę <font color="#FF00FF"><b>»»znaleźć««</b></font> pakiety na mój router wrt54g3g v1 bo linki w temacie wygasły . Lub może ktoś podrzuci na prv
ODPOWIEDZ