Huawei B525s-23a mod firmware.

Dyskusje na temat wyboru sprzętu. Jaki modem, telefon do GPRS/EDGE/UMTS/HSDPA/HSUPA, jaką przejściówkę, kabel do telefonu... itp. mam wybrać?

Moderator: Moderatorzy

ODPOWIEDZ
angben
Początkujący użytkownik forum
Posty: 4
Rejestracja: 2018-04-22, 13:39

Re: Huawei B525s-23a mod firmware.

Post autor: angben »

garysek pisze:
angben pisze:hi to all... i have b525 router too and i have installed correctly 1.1 firmware mod. There's a way to down the connection if the vpn stop work?
http://www.bez-kabli.pl/viewtopic.php?f ... 25#p574583
... but you need the firmware version 11.182.61.00.778_DB

Soon:
Obrazek

i have to install 11.182.61.00.778 only or after flash the firmware i have to do the command in ssh console?
Mek88
Początkujący użytkownik forum
Posty: 14
Rejestracja: 2018-04-11, 09:58

Re: Huawei B525s-23a mod firmware.

Post autor: Mek88 »

angben pisze:
garysek pisze:
angben pisze:hi to all... i have b525 router too and i have installed correctly 1.1 firmware mod. There's a way to down the connection if the vpn stop work?
http://www.bez-kabli.pl/viewtopic.php?f ... 25#p574583
... but you need the firmware version 11.182.61.00.778_DB

Soon:
Obrazek

i have to install 11.182.61.00.778 only or after flash the firmware i have to do the command in ssh console?
ATTENTION! i have already flash this firmware 11.182.61.00.778 but is not present " no internet if vpn is not connect "
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

][No_WaY pisze:I need to stop ipv6 connection trying as it not supported by my network , so it gives failed result in log file , because of that I'm trying to disable it and see if it is the reason behind traffic lag that forces me to reboot the router daily or twice per day!
My network also doesn't support IPV6 and I don't have to restart the router every day. The problem is probably somewhere else (B525s-65a ?). But you can choose the IP type on the "Profile Management" screen:
Obrazek

Mek88 pisze:ATTENTION! i have already flash this firmware 11.182.61.00.778 but is not present " no internet if vpn is not connect "
Ehhh... I wrote:
garysek pisze:Soon:
Now:
If you have firmware 11.182.61.00.778_DB (B525) or 11.237.01.01.801_DB (B528) give this commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /tmp/upgrade.sh -r /B52x/upgrade/upgrade.sh -P 18033 garysek.podlasie.pl
chmod 755 /tmp/upgrade.sh
/tmp/upgrade.sh mod150
Log:

Kod: Zaznacz cały

root@p722:/tmp # wget -g -l /tmp/upgrade.sh -r /B52x/upgrade/upgrade.sh -P 18033 garysek.podlasie.pl
The IP is [185.201.112.30]
root@p722:/tmp # chmod 755 /tmp/upgrade.sh
root@p722:/tmp # /tmp/upgrade.sh mod150
[UPGRADE] Downloading file mod150.tar.gz...
[UPGRADE] mod150.tar.gz succesfully downloaded
[MOD_150] Installing mod...
[MOD_150] Successfully upgraded
[MOD_150] Rebooting system...

After this you have:
WEBUI do routerów B52xs-23a
---------------------------

Mod1.5pl
Zmiany względem Mod1.4pl:
- dodane ustawienie "Brak Internetu przy rozłączonym VPN" (ekran VPN)

---------------------------
Mod1.4pl
Mod oparty na nowszej wersji webui (11.237.01.01.801). Zawiera w sobie chyba wszystkie modyfikacje, jakie miał mod1.3pl, ale ma mniej języków do wyboru. Natomiast dodatkowo:
- poprawiony ekran "Ustawienia sieci" - do wyboru są tylko częstotliwości obsługiwane przez router.
- przeorganizowana kolumna "Bieżące połączenie" na ekranie startowym
- dodana instrukcja obsługi w języku polskim (po kliknięciu "Pomoc" obok wyboru języka)
11.182.61.00.778_DBU
Zmiany względem 11.182.61.00.778_DB:
- dodano skrypt do kontroli VPN
- dodano skrypt do robienia upgrade'ów
Mek88
Początkujący użytkownik forum
Posty: 14
Rejestracja: 2018-04-11, 09:58

Re: Huawei B525s-23a mod firmware.

Post autor: Mek88 »

Mek88 pisze:ATTENTION! i have already flash this firmware 11.182.61.00.778 but is not present " no internet if vpn is not connect "
Ehhh... I wrote:
garysek pisze:Soon:
Now:
If you have firmware 11.182.61.00.778_DB (B525) or 11.237.01.01.801_DB (B528) give this commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /tmp/upgrade.sh -r /B52x/upgrade/upgrade.sh -P 18033 garysek.podlasie.pl
chmod 755 /tmp/upgrade.sh
/tmp/upgrade.sh mod150
Log:

Kod: Zaznacz cały

root@p722:/tmp # wget -g -l /tmp/upgrade.sh -r /B52x/upgrade/upgrade.sh -P 18033 garysek.podlasie.pl
The IP is [185.201.112.30]
root@p722:/tmp # chmod 755 /tmp/upgrade.sh
root@p722:/tmp # /tmp/upgrade.sh mod150
[UPGRADE] Downloading file mod150.tar.gz...
[UPGRADE] mod150.tar.gz succesfully downloaded
[MOD_150] Installing mod...
[MOD_150] Successfully upgraded
[MOD_150] Rebooting system...

After this you have:
WEBUI do routerów B52xs-23a
---------------------------

Mod1.5pl
Zmiany względem Mod1.4pl:
- dodane ustawienie "Brak Internetu przy rozłączonym VPN" (ekran VPN)

---------------------------
Mod1.4pl
Mod oparty na nowszej wersji webui (11.237.01.01.801). Zawiera w sobie chyba wszystkie modyfikacje, jakie miał mod1.3pl, ale ma mniej języków do wyboru. Natomiast dodatkowo:
- poprawiony ekran "Ustawienia sieci" - do wyboru są tylko częstotliwości obsługiwane przez router.
- przeorganizowana kolumna "Bieżące połączenie" na ekranie startowym
- dodana instrukcja obsługi w języku polskim (po kliknięciu "Pomoc" obok wyboru języka)
11.182.61.00.778_DBU
Zmiany względem 11.182.61.00.778_DB:
- dodano skrypt do kontroli VPN
- dodano skrypt do robienia upgrade'ów
[/quote]


GARYSEK Please help me.... I need to connect with OPENVPN protocol on my Huawei b525 :(
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

I don't know any OPENVPN client on B525.

P.S. Przydałby się moderator do porobienia porządku z tymi cytatami ;).
][No_WaY
Użytkownik forum
Posty: 34
Rejestracja: 2018-03-15, 12:37

Re: Huawei B525s-23a mod firmware.

Post autor: ][No_WaY »

garysek pisze:
angben pisze:hi to all... i have b525 router too and i have installed correctly 1.1 firmware mod. There's a way to down the connection if the vpn stop work?
http://www.bez-kabli.pl/viewtopic.php?f ... 25#p574583
... but you need the firmware version 11.182.61.00.778_DB

Soon:
Obrazek

][No_WaY pisze:can you please add B28 band to band selection

Kod: Zaznacz cały

root@p722:/ # wget -g -l /app/webroot/WebApp/common/js/mobilenetworksettings.js.gz -r /B525/mobilenetworksettings.js.gz -P 18033 garysek.podlasie.pl
The IP is [185.201.112.30]
root@p722:/ # wget -g -l /app/webroot/WebApp/common/html/mobilenetworksettings.html.gz -r /B525/mobilenetworksettings.html.gz -P 18033 garysek.podlasie.pl
The IP is [185.201.112.30]
root@p722:/ #
Obrazek

But I have no way to test if it works correctly...
][No_WaY pisze:and add ability to disable ipv6 connection?
I don't understand. What exactly do you need?
thank you B28 added and work perfect on B525-65s :)
can you add B2,B4,B5,B19,B26,B41 :papa:
to use it with wget and attach the file for future proof :D
][No_WaY
Użytkownik forum
Posty: 34
Rejestracja: 2018-03-15, 12:37

Re: Huawei B525s-23a mod firmware.

Post autor: ][No_WaY »

garysek pisze:
][No_WaY pisze:I need to stop ipv6 connection trying as it not supported by my network , so it gives failed result in log file , because of that I'm trying to disable it and see if it is the reason behind traffic lag that forces me to reboot the router daily or twice per day!
My network also doesn't support IPV6 and I don't have to restart the router every day. The problem is probably somewhere else (B525s-65a ?). But you can choose the IP type on the "Profile Management" screen:
Obrazek

on profile page it auto detect and add the profile and can not be changed neither deleted to add anew on with different setting :gwiazdki:
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

You can't delete or edit the default profile, but you can add a new one:
ObrazekObrazek
Then you can edit and delete this new profile.

][No_WaY pisze:thank you B28 added and work perfect on B525-65s :)
can you add B2,B4,B5,B19,B26,B41 :papa:
I can. Show me the result of the command only:

Kod: Zaznacz cały

atc at^syscfgex=?
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

@rust3028 dał dziś linka do tematu z jego kompilacją OPENVPN na E3372h
https://translate.googleusercontent.com ... ry51164315
Działa także na B525 i B528. Nie trzeba tylko w nich ładować modułu tun.ko, bo jest już w kernelu.

Kod: Zaznacz cały

root@p722:/online/openvpn # ./openvpn --config config.ovpn
Fri May  4 21:44:00 2018 OpenVPN 2.3.11 i686-pc-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Jul  8 2016
Fri May  4 21:44:00 2018 library versions: OpenSSL 1.0.2k  26 Jan 2017, LZO 2.09
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/key.key' is group or others accessible
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/ta.key' is group or others accessible
Fri May  4 21:44:00 2018 Control Channel Authentication: using '/online/openvpn/ta.key' as a OpenVPN static key file
Fri May  4 21:44:00 2018 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Socket Buffers: R=[180224->180224] S=[180224->180224]
Fri May  4 21:44:00 2018 UDPv4 link local: [undef]
Fri May  4 21:44:00 2018 UDPv4 link remote: [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 TLS: Initial packet from [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 VERIFY OK: depth=1...
Fri May  4 21:44:00 2018 VERIFY OK: nsCertType=SERVER
Fri May  4 21:44:00 2018 VERIFY OK: depth=0...
Fri May  4 21:44:01 2018 Data Channel Encrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Data Channel Decrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA
Fri May  4 21:44:01 2018 [SERVER] Peer Connection Initiated with [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:03 2018 SENT CONTROL [SERVER]: 'PUSH_REQUEST' (status=1)
Fri May  4 21:44:03 2018 PUSH: Received control message: 'PUSH_REPLY,topology subnet,route-gateway 10.30.0.1,ping 5,ping-restart 15,ifconfig 10.30.0.40 255.255.255.0'
Fri May  4 21:44:03 2018 OPTIONS IMPORT: timers and/or timeouts modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: --ifconfig/up options modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: route-related options modified
Fri May  4 21:44:03 2018 TUN/TAP device tap0 opened
Fri May  4 21:44:03 2018 TUN/TAP TX queue length set to 100
Fri May  4 21:44:03 2018 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Fri May  4 21:44:03 2018 /system/bin/ip link set dev tap0 up mtu 1500
Fri May  4 21:44:03 2018 /system/bin/ip addr add dev tap0 10.30.0.40/24 broadcast 10.30.0.255
Fri May  4 21:44:03 2018 Initialization Sequence Completed

Kod: Zaznacz cały

root@p722:/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         10.64.64.1      0.0.0.0         UG    0      0        0 eth_x
10.30.0.0       *               255.255.255.0   U     0      0        0 tap0
10.64.64.1      *               255.255.255.255 UH    0      0        0 eth_x
192.168.35.0    *               255.255.255.0   U     0      0        0 br0
root@p722:/ # ping 10.30.0.1
PING 10.30.0.1 (10.30.0.1): 56 data bytes
64 bytes from 10.30.0.1: seq=0 ttl=64 time=65.730 ms
64 bytes from 10.30.0.1: seq=1 ttl=64 time=36.990 ms
64 bytes from 10.30.0.1: seq=2 ttl=64 time=31.595 ms

--- 10.30.0.1 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 31.595/44.771/65.730 ms
root@p722:/ #
ligeza
Stały użytkownik forum
Posty: 74
Rejestracja: 2015-10-06, 09:50

Re: Huawei B525s-23a mod firmware.

Post autor: ligeza »

Czy jest możliwość zamieszczenia firmware B525s-23a_UPDATE_11.182.61.00.778_DB w formacie bin. Posiadam już zmodowany router i chciałbym go wgrać prze menu routera.
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

11.182.61.00.778_DBU
Zmiany względem 11.182.61.00.778_DB:
- dodano skrypt do kontroli VPN
- dodano skrypt do robienia upgrade'ów
- scalony z webui Mod1.5pl
B525s-23a_UPDATE_11.182.61.00.778_DBU.rar

Jest to wersja .exe i .bin z naniesionymi już ostatnimi poprawkami (to co po wykonaniu upgrade mod150). Samego wgrywania do routera nie sprawdzałem, ale powinno być OK.
ligeza
Stały użytkownik forum
Posty: 74
Rejestracja: 2015-10-06, 09:50

Re: Huawei B525s-23a mod firmware.

Post autor: ligeza »

Dziękuję bardzo, wersja .bin wgrała się bez najmniejszego problemu.
][No_WaY
Użytkownik forum
Posty: 34
Rejestracja: 2018-03-15, 12:37

Re: Huawei B525s-23a mod firmware.

Post autor: ][No_WaY »

garysek pisze:You can't delete or edit the default profile, but you can add a new one:
ObrazekObrazek
Then you can edit and delete this new profile.

][No_WaY pisze:thank you B28 added and work perfect on B525-65s :)
can you add B2,B4,B5,B19,B26,B41 :papa:
I can. Show me the result of the command only:

Kod: Zaznacz cały

atc at^syscfgex=?
thanks this the result

atc at^syscfgex=?

^SYSCFGEX: ("00","01","02","03","99"),((1002000008400380,"GSM900/GSM1800/WCDMA BCVI/WCDMA BCVIII/WCDMA BCI/WCDMA BCXIX"),(4a80000,"GSM850/GSM1900/WCDMA BCV/WCDMA BCII"),(3fffffff,"All bands")),(0-2),(0-4),((1a08a0c00df,"LTE BC1/LTE BC2/LTE BC3/LTE BC4/LTE BC5/LTE BC7/LTE BC8/LTE BC19/LTE BC20/LTE BC26/LTE BC28/LTE BC32/LTE BC38/LTE BC40/LTE BC41"),(7fffffffffffffff,"All bands"))

OK
root@p722:/ #
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

in console ssh (firmware ..._DBU):

Kod: Zaznacz cały

upgrade mobilenetworksettings_65a
Log:

Kod: Zaznacz cały

root@p722:/ # upgrade mobilenetworksettings_65a
[UPGRADE] Downloading file mobilenetworksettings_65a.tar.gz...
[UPGRADE] mobilenetworksettings_65a.tar.gz succesfully downloaded
[MNS_65a] mobilenetworksettings B525s-65a successfully upgraded
root@p722:/ #
I also added the UMTS bands B2, B5, B6, and B19.


Możecie też sobie z ciekawości zobaczyć obfitość pasm w wersji 65a wykonując to polecenie. Chociaż w naszym kraju i tak pożytku z nich nie byłoby. Aby mieć do wyboru tylko pasma obsługiwane przez wersję 23a wystarczy później komenda:

Kod: Zaznacz cały

upgrade mobilenetworksettings_23a
P.S. Aby działał skrypt upgrade router musi mieć połączenie z Internetem, czyli np. w trybie mostu nie zadziała...
][No_WaY
Użytkownik forum
Posty: 34
Rejestracja: 2018-03-15, 12:37

Re: Huawei B525s-23a mod firmware.

Post autor: ][No_WaY »

garysek pisze:in console ssh (firmware ..._DBU):

Kod: Zaznacz cały

upgrade mobilenetworksettings_65a
Log:

Kod: Zaznacz cały

root@p722:/ # upgrade mobilenetworksettings_65a
[UPGRADE] Downloading file mobilenetworksettings_65a.tar.gz...
[UPGRADE] mobilenetworksettings_65a.tar.gz succesfully downloaded
[MNS_65a] mobilenetworksettings B525s-65a successfully upgraded
root@p722:/ #
I also added the UMTS bands B2, B5, B6, and B19.


Możecie też sobie z ciekawości zobaczyć obfitość pasm w wersji 65a wykonując to polecenie. Chociaż w naszym kraju i tak pożytku z nich nie byłoby. Aby mieć do wyboru tylko pasma obsługiwane przez wersję 23a wystarczy później komenda:

Kod: Zaznacz cały

upgrade mobilenetworksettings_23a
P.S. Aby działał skrypt upgrade router musi mieć połączenie z Internetem, czyli np. w trybie mostu nie zadziała...
thank you very much for your help and support
can you take alook on this firmware
B525s-95a_UPDATE_11.187.61.01.1133.rar
https://gulfupload.com/vnbu1wv0a2mx

it is my regional firmware , I hope it can support bridge mode and other mods(all band + anttena setting + manual dns .. etc)

thanks again
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

But you have version 65a, not 95a.
At the factory, this software doesn't support bridge mode and other modes. Unfortunately, the webui of this software is newer and doesn't work with my soft, so I can't check it out. I added ssh and other modifications to this and linked to my webui. Maybe it will work. I also added Arabic to webui, but I don't think it looks correct.
B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar
alcoo
Użytkownik forum
Posty: 30
Rejestracja: 2017-12-02, 18:40
Lokalizacja: Kraków

Re: Huawei B525s-23a mod firmware.

Post autor: alcoo »

garysek pisze:
11.182.61.00.778_DBU
Zmiany względem 11.182.61.00.778_DB:
- dodano skrypt do kontroli VPN
- dodano skrypt do robienia upgrade'ów
- scalony z webui Mod1.5pl
B525s-23a_UPDATE_11.182.61.00.778_DBU.rar

Jest to wersja .exe i .bin z naniesionymi już ostatnimi poprawkami (to co po wykonaniu upgrade mod150). Samego wgrywania do routera nie sprawdzałem, ale powinno być OK.
Witam,
mam wersję B525s-23a_UPDATE_11.182.61.00.778_DB z wykonanym updatem przez shh. Czy jest konieczność wykonania aktualizacji do wersji B525s-23a_UPDATE_11.182.61.00.778_DBU ze względu na ten wpis:
- dodano skrypt do robienia upgrade'ów


Jeśli tak, to czy przejdzie przez plik *.bin? Czy trzeba znowu rozkręcać?

Dzięki za wyjaśnienia.

Brawo za bardzo dobrą pracę.
][No_WaY
Użytkownik forum
Posty: 34
Rejestracja: 2018-03-15, 12:37

Re: Huawei B525s-23a mod firmware.

Post autor: ][No_WaY »

garysek pisze:But you have version 65a, not 95a.
At the factory, this software doesn't support bridge mode and other modes. Unfortunately, the webui of this software is newer and doesn't work with my soft, so I can't check it out. I added ssh and other modifications to this and linked to my webui. Maybe it will work. I also added Arabic to webui, but I don't think it looks correct.
B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar
can i update it directly from webui of B525s-23a_UPDATE_11.182.61.00.778_DBU os should use shorting method?
and from testing 65a can use 23a and 95a :szok:
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

- dodano skrypt do robienia upgrade'ów

@alcoo, przecież to samo miałeś napisane w poście opisującym jak po ssh update zrobić.
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575297
Jeśli zrobiłeś jak tam opisane to masz dokładnie to samo.
Zresztą sprawdź jak to działa:
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575374

][No_WaY pisze: can i update it directly from webui of B525s-23a_UPDATE_11.182.61.00.778_DBU os should use shorting method?
No, this is completely new software, you will not upload it via webui.
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

and from testing 65a can use 23a and 95a :szok:
I don't give a guarantee that it will work, in the worst case you will re-upload the old software.

All in all, since it is not software from your model anyway, there is no reason to upload.
alcoo
Użytkownik forum
Posty: 30
Rejestracja: 2017-12-02, 18:40
Lokalizacja: Kraków

Re: Huawei B525s-23a mod firmware.

Post autor: alcoo »

garysek pisze: @alcoo, przecież to samo miałeś napisane w poście opisującym jak po ssh update zrobić.
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575297
Tak mi się wydawało. Wolałem dopytać, ponieważ nie byłem pewien z tym skryptem... a może coś innego.
garysek pisze: Zresztą sprawdź jak to działa:
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575374
Jak działa jeszcze nie sprawdzałem. Wygląda tak:
IMG_20180505_225517.png
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

Daj zrzut po:

Kod: Zaznacz cały

upgrade mobilenetworksettings_65a
Mek88
Początkujący użytkownik forum
Posty: 14
Rejestracja: 2018-04-11, 09:58

Re: Huawei B525s-23a mod firmware.

Post autor: Mek88 »

garysek pisze:@rust3028 dał dziś linka do tematu z jego kompilacją OPENVPN na E3372h
https://translate.googleusercontent.com ... ry51164315
Działa także na B525 i B528. Nie trzeba tylko w nich ładować modułu tun.ko, bo jest już w kernelu.

Kod: Zaznacz cały

root@p722:/online/openvpn # ./openvpn --config config.ovpn
Fri May  4 21:44:00 2018 OpenVPN 2.3.11 i686-pc-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Jul  8 2016
Fri May  4 21:44:00 2018 library versions: OpenSSL 1.0.2k  26 Jan 2017, LZO 2.09
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/key.key' is group or others accessible
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/ta.key' is group or others accessible
Fri May  4 21:44:00 2018 Control Channel Authentication: using '/online/openvpn/ta.key' as a OpenVPN static key file
Fri May  4 21:44:00 2018 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Socket Buffers: R=[180224->180224] S=[180224->180224]
Fri May  4 21:44:00 2018 UDPv4 link local: [undef]
Fri May  4 21:44:00 2018 UDPv4 link remote: [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 TLS: Initial packet from [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 VERIFY OK: depth=1...
Fri May  4 21:44:00 2018 VERIFY OK: nsCertType=SERVER
Fri May  4 21:44:00 2018 VERIFY OK: depth=0...
Fri May  4 21:44:01 2018 Data Channel Encrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Data Channel Decrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA
Fri May  4 21:44:01 2018 [SERVER] Peer Connection Initiated with [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:03 2018 SENT CONTROL [SERVER]: 'PUSH_REQUEST' (status=1)
Fri May  4 21:44:03 2018 PUSH: Received control message: 'PUSH_REPLY,topology subnet,route-gateway 10.30.0.1,ping 5,ping-restart 15,ifconfig 10.30.0.40 255.255.255.0'
Fri May  4 21:44:03 2018 OPTIONS IMPORT: timers and/or timeouts modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: --ifconfig/up options modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: route-related options modified
Fri May  4 21:44:03 2018 TUN/TAP device tap0 opened
Fri May  4 21:44:03 2018 TUN/TAP TX queue length set to 100
Fri May  4 21:44:03 2018 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Fri May  4 21:44:03 2018 /system/bin/ip link set dev tap0 up mtu 1500
Fri May  4 21:44:03 2018 /system/bin/ip addr add dev tap0 10.30.0.40/24 broadcast 10.30.0.255
Fri May  4 21:44:03 2018 Initialization Sequence Completed

Kod: Zaznacz cały

root@p722:/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         10.64.64.1      0.0.0.0         UG    0      0        0 eth_x
10.30.0.0       *               255.255.255.0   U     0      0        0 tap0
10.64.64.1      *               255.255.255.255 UH    0      0        0 eth_x
192.168.35.0    *               255.255.255.0   U     0      0        0 br0
root@p722:/ # ping 10.30.0.1
PING 10.30.0.1 (10.30.0.1): 56 data bytes
64 bytes from 10.30.0.1: seq=0 ttl=64 time=65.730 ms
64 bytes from 10.30.0.1: seq=1 ttl=64 time=36.990 ms
64 bytes from 10.30.0.1: seq=2 ttl=64 time=31.595 ms

--- 10.30.0.1 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 31.595/44.771/65.730 ms
root@p722:/ #
I have saw that, But I did not understand how he did it..... :/
][No_WaY
Użytkownik forum
Posty: 34
Rejestracja: 2018-03-15, 12:37

Re: Huawei B525s-23a mod firmware.

Post autor: ][No_WaY »

garysek pisze:But you have version 65a, not 95a.
At the factory, this software doesn't support bridge mode and other modes. Unfortunately, the webui of this software is newer and doesn't work with my soft, so I can't check it out. I added ssh and other modifications to this and linked to my webui. Maybe it will work. I also added Arabic to webui, but I don't think it looks correct.
B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar
thank you very much is working perfectly, only telnet not connecting but adb is working , can be solved?
did you add 65a network setting to this firm? because i found all the band without adb command!
Mek88
Początkujący użytkownik forum
Posty: 14
Rejestracja: 2018-04-11, 09:58

Re: Huawei B525s-23a mod firmware.

Post autor: Mek88 »

Mek88 pisze:
garysek pisze:@rust3028 dał dziś linka do tematu z jego kompilacją OPENVPN na E3372h
https://translate.googleusercontent.com ... ry51164315
Działa także na B525 i B528. Nie trzeba tylko w nich ładować modułu tun.ko, bo jest już w kernelu.

Kod: Zaznacz cały

root@p722:/online/openvpn # ./openvpn --config config.ovpn
Fri May  4 21:44:00 2018 OpenVPN 2.3.11 i686-pc-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Jul  8 2016
Fri May  4 21:44:00 2018 library versions: OpenSSL 1.0.2k  26 Jan 2017, LZO 2.09
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/key.key' is group or others accessible
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/ta.key' is group or others accessible
Fri May  4 21:44:00 2018 Control Channel Authentication: using '/online/openvpn/ta.key' as a OpenVPN static key file
Fri May  4 21:44:00 2018 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Socket Buffers: R=[180224->180224] S=[180224->180224]
Fri May  4 21:44:00 2018 UDPv4 link local: [undef]
Fri May  4 21:44:00 2018 UDPv4 link remote: [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 TLS: Initial packet from [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 VERIFY OK: depth=1...
Fri May  4 21:44:00 2018 VERIFY OK: nsCertType=SERVER
Fri May  4 21:44:00 2018 VERIFY OK: depth=0...
Fri May  4 21:44:01 2018 Data Channel Encrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Data Channel Decrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA
Fri May  4 21:44:01 2018 [SERVER] Peer Connection Initiated with [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:03 2018 SENT CONTROL [SERVER]: 'PUSH_REQUEST' (status=1)
Fri May  4 21:44:03 2018 PUSH: Received control message: 'PUSH_REPLY,topology subnet,route-gateway 10.30.0.1,ping 5,ping-restart 15,ifconfig 10.30.0.40 255.255.255.0'
Fri May  4 21:44:03 2018 OPTIONS IMPORT: timers and/or timeouts modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: --ifconfig/up options modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: route-related options modified
Fri May  4 21:44:03 2018 TUN/TAP device tap0 opened
Fri May  4 21:44:03 2018 TUN/TAP TX queue length set to 100
Fri May  4 21:44:03 2018 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Fri May  4 21:44:03 2018 /system/bin/ip link set dev tap0 up mtu 1500
Fri May  4 21:44:03 2018 /system/bin/ip addr add dev tap0 10.30.0.40/24 broadcast 10.30.0.255
Fri May  4 21:44:03 2018 Initialization Sequence Completed

Kod: Zaznacz cały

root@p722:/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         10.64.64.1      0.0.0.0         UG    0      0        0 eth_x
10.30.0.0       *               255.255.255.0   U     0      0        0 tap0
10.64.64.1      *               255.255.255.255 UH    0      0        0 eth_x
192.168.35.0    *               255.255.255.0   U     0      0        0 br0
root@p722:/ # ping 10.30.0.1
PING 10.30.0.1 (10.30.0.1): 56 data bytes
64 bytes from 10.30.0.1: seq=0 ttl=64 time=65.730 ms
64 bytes from 10.30.0.1: seq=1 ttl=64 time=36.990 ms
64 bytes from 10.30.0.1: seq=2 ttl=64 time=31.595 ms

--- 10.30.0.1 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 31.595/44.771/65.730 ms
root@p722:/ #
I have saw that, But I did not understand how he did it..... :/

Now i have that problem....
alcoo
Użytkownik forum
Posty: 30
Rejestracja: 2017-12-02, 18:40
Lokalizacja: Kraków

Re: Huawei B525s-23a mod firmware.

Post autor: alcoo »

garysek pisze:Daj zrzut po:

Kod: Zaznacz cały

upgrade mobilenetworksettings_65a
a proszę:
Obrazek
Mek88
Początkujący użytkownik forum
Posty: 14
Rejestracja: 2018-04-11, 09:58

Re: Huawei B525s-23a mod firmware.

Post autor: Mek88 »

Im blocked ...... I dont know how can i do to install openvpn :
IMG_20180506_231912_451.jpg
alcoo
Użytkownik forum
Posty: 30
Rejestracja: 2017-12-02, 18:40
Lokalizacja: Kraków

Re: Huawei B525s-23a mod firmware.

Post autor: alcoo »

Zauważyłem, że na nowym firmware B525s-23a_UPDATE_11.182.61.00.778_DBU router bardzo szybko zmienia pasma transmisji danych. To na plus.

Do tej pory leciałem na paśmie 2600MHz a teraz z automatu mi się przełącza na 1800. No i nie widzę żeby następowała agredacja łącza (4G+). W zasięgu mam jeszcze 800MHz. Czyli router powinien pociągnąć na dwóch pasmach tak jak wcześniej.

Czy zauwaliście podobne objawy? Czy to coś się dzieje z nadajnikami?
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

][No_WaY pisze:thank you very much is working perfectly, only telnet not connecting but adb is working , can be solved?
did you add 65a network setting to this firm? because i found all the band without adb command!
I just added ssh, as in the 11.182.61.00.778_DBU firmware. Does ssh work? If you want telnet, type in the console:

Kod: Zaznacz cały

busyboxx telnetd -l /bin/sh
If you want to permanently type it:

Kod: Zaznacz cały

echo "busyboxx telnetd -l /bin/sh" >> /etc/autorun.sh
I don't know why ADB works, I didn't add it. Yes, I added mobilenetworksettings_65a.

Mek88 pisze:Im blocked ...... I dont know how can i do to install openvpn :
Easy, @rust3028 only gave the binary. It is necessary to set up iptables (what he gave to B315 is not enough), routing table, etc. As I write the appropriate scripts I will make them available. Wait, but don't expect webui support.

alcoo pisze:Czy zauwaliście podobne objawy? Czy to coś się dzieje z nadajnikami?
Ja niestety nie jestem w zasięgu agregacji, chyba że aero2 sobie podładuję to może 800+1800 złapię. Temat warty sprawdzenia. A może tylko znaczka 4G+ nie pokazuje? Chociaż wydaje mi się, że powinien.
garysek
Stały użytkownik forum
Posty: 149
Rejestracja: 2017-04-03, 19:44

Re: Huawei B525s-23a mod firmware.

Post autor: garysek »

Obrazek

Działa zarówno 800+1800 jak i 1800+800. Nic więcej nie sprawdzę.

4G+ pojawia się tylko podczas większego zapotrzebowania na transfer (w moim przypadku speedtest), jak nie ma dużego transferu to od razu zrzuca do 4G.
ODPOWIEDZ