witam
Rzeczywiście telefon był pod ttyACM0. Spróbowałem konfiguracji poprzez wvdial :
Kod: Zaznacz cały
[root@localhost ~]# wvdialconf /etc/wvdial.conf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttyACM0<*1>: ATQ0 V1 E1 -- OK
ttyACM0<*1>: ATQ0 V1 E1 Z -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyACM0<*1>: Modem Identifier: ATI -- Manufacturer: SAMSUNG ELECTRONICS CORPORATION
ttyACM0<*1>: Speed 4800: AT -- OK
ttyACM0<*1>: Speed 9600: AT -- OK
ttyACM0<*1>: Speed 19200: AT -- OK
ttyACM0<*1>: Speed 38400: AT -- OK
ttyACM0<*1>: Speed 57600: AT -- OK
ttyACM0<*1>: Speed 115200: AT -- OK
ttyACM0<*1>: Speed 230400: AT -- OK
ttyACM0<*1>: Speed 460800: AT -- OK
ttyACM0<*1>: Max speed is 460800; that should be safe.
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found an USB modem on /dev/ttyACM0.
/etc/wvdial.conf<Warn>: Can't open '/etc/wvdial.conf' for reading: No such file or directory
/etc/wvdial.conf<Warn>: ...starting with blank configuration.
Modem configuration written to /etc/wvdial.conf.
ttyACM0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
[root@localhost ~]#
Plik konfiguracyjny mam taki :
Kod: Zaznacz cały
[Dialer Defaults]
Dial Command = ATDT
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2
Init3 = AT+CGDCONT=1,"IP","internet"
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
Baud = 460800
Phone = *99#
Username = "blank"
Password = "blank"
Stupid Mode = yes
i uzyskałem połączenie :
Kod: Zaznacz cały
[root@localhost ~]# wvdial
--> WvDial: Internet dialer version 1.61
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
ATQ0 V1 E1 S0=0 &C1 &D2
OK
--> Sending: AT+CGDCONT=1,"IP","internet"
AT+CGDCONT=1,"IP","internet"
OK
--> Modem initialized.
--> Sending: ATDT*99#
--> Waiting for carrier.
ATDT*99#
CONNECT 7200000
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Sat Nov 17 19:37:04 2012
--> Pid of pppd: 7295
--> Using interface ppp0
--> pppd: Connect: ppp0 <--> /dev/ttyACM0
--> pppd: CHAP authentication succeeded
--> pppd: CHAP authentication succeeded
--> pppd: Could not determine remote IP address: defaulting to 10.64.64.64
--> local IP address 37.225.10.91
--> remote IP address 10.64.64.64
--> primary DNS address 79.163.127.70
--> secondary DNS address 217.116.100.65
I tutaj mam pytanie jak to zrobić w trybie graficznym? Oraz co zrobić żeby zakończyć połączenie poprzez wvdial?
