Huawei B525s-23a mod firmware.

[garysek]

But you have version 65a, not 95a.
At the factory, this software doesn't support bridge mode and other modes. Unfortunately, the webui of this software is newer and doesn't work with my soft, so I can't check it out. I added ssh and other modifications to this and linked to my webui. Maybe it will work. I also added Arabic to webui, but I don't think it looks correct.
B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar

[alcoo]

11.182.61.00.778_DBU
Zmiany względem 11.182.61.00.778_DB:
- dodano skrypt do kontroli VPN
- dodano skrypt do robienia upgrade'ów
- scalony z webui Mod1.5pl

B525s-23a_UPDATE_11.182.61.00.778_DBU.rar

Jest to wersja .exe i .bin z naniesionymi już ostatnimi poprawkami (to co po wykonaniu upgrade mod150). Samego wgrywania do routera nie sprawdzałem, ale powinno być OK.

Witam,
mam wersję B525s-23a_UPDATE_11.182.61.00.778_DB z wykonanym updatem przez shh. Czy jest konieczność wykonania aktualizacji do wersji B525s-23a_UPDATE_11.182.61.00.778_DBU ze względu na ten wpis:

- dodano skrypt do robienia upgrade'ów

Jeśli tak, to czy przejdzie przez plik *.bin? Czy trzeba znowu rozkręcać?

Dzięki za wyjaśnienia.

Brawo za bardzo dobrą pracę.

[][No_WaY]

But you have version 65a, not 95a.
At the factory, this software doesn't support bridge mode and other modes. Unfortunately, the webui of this software is newer and doesn't work with my soft, so I can't check it out. I added ssh and other modifications to this and linked to my webui. Maybe it will work. I also added Arabic to webui, but I don't think it looks correct.
B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar

can i update it directly from webui of B525s-23a_UPDATE_11.182.61.00.778_DBU os should use shorting method?
and from testing 65a can use 23a and 95a

[garysek]

- dodano skrypt do robienia upgrade'ów

@alcoo, przecież to samo miałeś napisane w poście opisującym jak po ssh update zrobić.
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575297
Jeśli zrobiłeś jak tam opisane to masz dokładnie to samo.
Zresztą sprawdź jak to działa:
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575374

can i update it directly from webui of B525s-23a_UPDATE_11.182.61.00.778_DBU os should use shorting method?

No, this is completely new software, you will not upload it via webui.

[garysek]

and from testing 65a can use 23a and 95a

I don't give a guarantee that it will work, in the worst case you will re-upload the old software.

All in all, since it is not software from your model anyway, there is no reason to upload.

[alcoo]

@alcoo, przecież to samo miałeś napisane w poście opisującym jak po ssh update zrobić.
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575297

Tak mi się wydawało. Wolałem dopytać, ponieważ nie byłem pewien z tym skryptem... a może coś innego.

Zresztą sprawdź jak to działa:
http://www.bez-kabli.pl/viewtopic.php?f ... 55#p575374

Jak działa jeszcze nie sprawdzałem. Wygląda tak:

IMG_20180505_225517.png

[garysek]

Daj zrzut po:

Kod: Zaznacz cały

upgrade mobilenetworksettings_65a

[Mek88]

@rust3028 dał dziś linka do tematu z jego kompilacją OPENVPN na E3372h
https://translate.googleusercontent.com ... ry51164315
Działa także na B525 i B528. Nie trzeba tylko w nich ładować modułu tun.ko, bo jest już w kernelu.

Kod: Zaznacz cały

root@p722:/online/openvpn # ./openvpn --config config.ovpn
Fri May  4 21:44:00 2018 OpenVPN 2.3.11 i686-pc-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Jul  8 2016
Fri May  4 21:44:00 2018 library versions: OpenSSL 1.0.2k  26 Jan 2017, LZO 2.09
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/key.key' is group or others accessible
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/ta.key' is group or others accessible
Fri May  4 21:44:00 2018 Control Channel Authentication: using '/online/openvpn/ta.key' as a OpenVPN static key file
Fri May  4 21:44:00 2018 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Socket Buffers: R=[180224->180224] S=[180224->180224]
Fri May  4 21:44:00 2018 UDPv4 link local: [undef]
Fri May  4 21:44:00 2018 UDPv4 link remote: [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 TLS: Initial packet from [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 VERIFY OK: depth=1...
Fri May  4 21:44:00 2018 VERIFY OK: nsCertType=SERVER
Fri May  4 21:44:00 2018 VERIFY OK: depth=0...
Fri May  4 21:44:01 2018 Data Channel Encrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Data Channel Decrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA
Fri May  4 21:44:01 2018 [SERVER] Peer Connection Initiated with [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:03 2018 SENT CONTROL [SERVER]: 'PUSH_REQUEST' (status=1)
Fri May  4 21:44:03 2018 PUSH: Received control message: 'PUSH_REPLY,topology subnet,route-gateway 10.30.0.1,ping 5,ping-restart 15,ifconfig 10.30.0.40 255.255.255.0'
Fri May  4 21:44:03 2018 OPTIONS IMPORT: timers and/or timeouts modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: --ifconfig/up options modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: route-related options modified
Fri May  4 21:44:03 2018 TUN/TAP device tap0 opened
Fri May  4 21:44:03 2018 TUN/TAP TX queue length set to 100
Fri May  4 21:44:03 2018 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Fri May  4 21:44:03 2018 /system/bin/ip link set dev tap0 up mtu 1500
Fri May  4 21:44:03 2018 /system/bin/ip addr add dev tap0 10.30.0.40/24 broadcast 10.30.0.255
Fri May  4 21:44:03 2018 Initialization Sequence Completed

Kod: Zaznacz cały

root@p722:/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         10.64.64.1      0.0.0.0         UG    0      0        0 eth_x
10.30.0.0       *               255.255.255.0   U     0      0        0 tap0
10.64.64.1      *               255.255.255.255 UH    0      0        0 eth_x
192.168.35.0    *               255.255.255.0   U     0      0        0 br0
root@p722:/ # ping 10.30.0.1
PING 10.30.0.1 (10.30.0.1): 56 data bytes
64 bytes from 10.30.0.1: seq=0 ttl=64 time=65.730 ms
64 bytes from 10.30.0.1: seq=1 ttl=64 time=36.990 ms
64 bytes from 10.30.0.1: seq=2 ttl=64 time=31.595 ms

--- 10.30.0.1 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 31.595/44.771/65.730 ms
root@p722:/ #

I have saw that, But I did not understand how he did it.....

[][No_WaY]

But you have version 65a, not 95a.
At the factory, this software doesn't support bridge mode and other modes. Unfortunately, the webui of this software is newer and doesn't work with my soft, so I can't check it out. I added ssh and other modifications to this and linked to my webui. Maybe it will work. I also added Arabic to webui, but I don't think it looks correct.
B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar

thank you very much is working perfectly, only telnet not connecting but adb is working , can be solved?
did you add 65a network setting to this firm? because i found all the band without adb command!

[Mek88]

@rust3028 dał dziś linka do tematu z jego kompilacją OPENVPN na E3372h
https://translate.googleusercontent.com ... ry51164315
Działa także na B525 i B528. Nie trzeba tylko w nich ładować modułu tun.ko, bo jest już w kernelu.

Kod: Zaznacz cały

root@p722:/online/openvpn # ./openvpn --config config.ovpn
Fri May  4 21:44:00 2018 OpenVPN 2.3.11 i686-pc-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Jul  8 2016
Fri May  4 21:44:00 2018 library versions: OpenSSL 1.0.2k  26 Jan 2017, LZO 2.09
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/key.key' is group or others accessible
Fri May  4 21:44:00 2018 WARNING: file '/online/openvpn/ta.key' is group or others accessible
Fri May  4 21:44:00 2018 Control Channel Authentication: using '/online/openvpn/ta.key' as a OpenVPN static key file
Fri May  4 21:44:00 2018 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:00 2018 Socket Buffers: R=[180224->180224] S=[180224->180224]
Fri May  4 21:44:00 2018 UDPv4 link local: [undef]
Fri May  4 21:44:00 2018 UDPv4 link remote: [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 TLS: Initial packet from [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:00 2018 VERIFY OK: depth=1...
Fri May  4 21:44:00 2018 VERIFY OK: nsCertType=SERVER
Fri May  4 21:44:00 2018 VERIFY OK: depth=0...
Fri May  4 21:44:01 2018 Data Channel Encrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Data Channel Decrypt: Cipher 'AES-256-CBC' initialized with 256 bit key
Fri May  4 21:44:01 2018 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri May  4 21:44:01 2018 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA
Fri May  4 21:44:01 2018 [SERVER] Peer Connection Initiated with [AF_INET]xx.xx.xx.xx:xx
Fri May  4 21:44:03 2018 SENT CONTROL [SERVER]: 'PUSH_REQUEST' (status=1)
Fri May  4 21:44:03 2018 PUSH: Received control message: 'PUSH_REPLY,topology subnet,route-gateway 10.30.0.1,ping 5,ping-restart 15,ifconfig 10.30.0.40 255.255.255.0'
Fri May  4 21:44:03 2018 OPTIONS IMPORT: timers and/or timeouts modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: --ifconfig/up options modified
Fri May  4 21:44:03 2018 OPTIONS IMPORT: route-related options modified
Fri May  4 21:44:03 2018 TUN/TAP device tap0 opened
Fri May  4 21:44:03 2018 TUN/TAP TX queue length set to 100
Fri May  4 21:44:03 2018 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Fri May  4 21:44:03 2018 /system/bin/ip link set dev tap0 up mtu 1500
Fri May  4 21:44:03 2018 /system/bin/ip addr add dev tap0 10.30.0.40/24 broadcast 10.30.0.255
Fri May  4 21:44:03 2018 Initialization Sequence Completed

Kod: Zaznacz cały

root@p722:/ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         10.64.64.1      0.0.0.0         UG    0      0        0 eth_x
10.30.0.0       *               255.255.255.0   U     0      0        0 tap0
10.64.64.1      *               255.255.255.255 UH    0      0        0 eth_x
192.168.35.0    *               255.255.255.0   U     0      0        0 br0
root@p722:/ # ping 10.30.0.1
PING 10.30.0.1 (10.30.0.1): 56 data bytes
64 bytes from 10.30.0.1: seq=0 ttl=64 time=65.730 ms
64 bytes from 10.30.0.1: seq=1 ttl=64 time=36.990 ms
64 bytes from 10.30.0.1: seq=2 ttl=64 time=31.595 ms

--- 10.30.0.1 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 31.595/44.771/65.730 ms
root@p722:/ #

I have saw that, But I did not understand how he did it.....

Now i have that problem....

[alcoo]

Daj zrzut po:

Kod: Zaznacz cały

upgrade mobilenetworksettings_65a

a proszę:

[Mek88]

Im blocked ...... I dont know how can i do to install openvpn :

IMG_20180506_231912_451.jpg

[alcoo]

Zauważyłem, że na nowym firmware B525s-23a_UPDATE_11.182.61.00.778_DBU router bardzo szybko zmienia pasma transmisji danych. To na plus.

Do tej pory leciałem na paśmie 2600MHz a teraz z automatu mi się przełącza na 1800. No i nie widzę żeby następowała agredacja łącza (4G+). W zasięgu mam jeszcze 800MHz. Czyli router powinien pociągnąć na dwóch pasmach tak jak wcześniej.

Czy zauwaliście podobne objawy? Czy to coś się dzieje z nadajnikami?

[garysek]

thank you very much is working perfectly, only telnet not connecting but adb is working , can be solved?
did you add 65a network setting to this firm? because i found all the band without adb command!

I just added ssh, as in the 11.182.61.00.778_DBU firmware. Does ssh work? If you want telnet, type in the console:

Kod: Zaznacz cały

busyboxx telnetd -l /bin/sh

If you want to permanently type it:

Kod: Zaznacz cały

echo "busyboxx telnetd -l /bin/sh" >> /etc/autorun.sh

I don't know why ADB works, I didn't add it. Yes, I added mobilenetworksettings_65a.

Im blocked ...... I dont know how can i do to install openvpn :

Easy, @rust3028 only gave the binary. It is necessary to set up iptables (what he gave to B315 is not enough), routing table, etc. As I write the appropriate scripts I will make them available. Wait, but don't expect webui support.

Czy zauwaliście podobne objawy? Czy to coś się dzieje z nadajnikami?

Ja niestety nie jestem w zasięgu agregacji, chyba że aero2 sobie podładuję to może 800+1800 złapię. Temat warty sprawdzenia. A może tylko znaczka 4G+ nie pokazuje? Chociaż wydaje mi się, że powinien.

[garysek]

Działa zarówno 800+1800 jak i 1800+800. Nic więcej nie sprawdzę.

4G+ pojawia się tylko podczas większego zapotrzebowania na transfer (w moim przypadku speedtest), jak nie ma dużego transferu to od razu zrzuca do 4G.

[][No_WaY]

Zauważyłem, że na nowym firmware B525s-23a_UPDATE_11.182.61.00.778_DBU router bardzo szybko zmienia pasma transmisji danych. To na plus.

Do tej pory leciałem na paśmie 2600MHz a teraz z automatu mi się przełącza na 1800. No i nie widzę żeby następowała agredacja łącza (4G+). W zasięgu mam jeszcze 800MHz. Czyli router powinien pociągnąć na dwóch pasmach tak jak wcześniej.

Czy zauwaliście podobne objawy? Czy to coś się dzieje z nadajnikami?

try to start download large file and open router webui and see if the 4g+ apperers .

[alcoo]

Czyli problemu nie mam. Dzięki za sprawdzenie.

[][No_WaY]

thank you very much is working perfectly, only telnet not connecting but adb is working , can be solved?
did you add 65a network setting to this firm? because i found all the band without adb command!

I just added ssh, as in the 11.182.61.00.778_DBU firmware. Does ssh work? If you want telnet, type in the console:

Kod: Zaznacz cały

busyboxx telnetd -l /bin/sh

If you want to permanently type it:

Kod: Zaznacz cały

echo "busyboxx telnetd -l /bin/sh" >> /etc/autorun.sh

I don't know why ADB works, I didn't add it. Yes, I added mobilenetworksettings_65a.

yes I meant SHH not ADB and i was refer to B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar not 11.182.61.00.778_DBU
I used the shh command that you attached to enable telnet and it is working perfectly
can you add it to the B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar so it will be complete exe or bin without any need to add shh command?

[][No_WaY]

Czyli problemu nie mam. Dzięki za sprawdzenie.

If you want full time 4g+ you can try B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar
despite you are using different model 23a but upon my experience it will work
try it on your own responsibility

[alcoo]

Thank you, I will not change anything.
I checked, in my area where I live, a new LTE transmitter on the 1800MHz band was probably installed, because on my site http://beta.btsearch.pl/ there are only 2600 MHz LTE transmitters. Now I connected with the LTE 32924161 transmitter and can't find it on the website http://beta.btsearch.pl/. I don't want to look at official websites and verify, because data rates have not deteriorated.

[garysek]

yes I meant SHH not ADB and i was refer to B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar not 11.182.61.00.778_DBU

I know. In both SSH it's just the same.

I used the shh command that you attached to enable telnet but when i try to connect to the telnet on port 23 it looks like it connect to shh!

It's telnet.

i cant use ati command!

Do you mean the ATC program? Should it work ... If it doesn't work then maybe because of firmware up to 95a?

If you want full time 4g+ you can try B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar
despite you are using different model 23a but upon my experience it will work
try it on your own responsibility

Może ktoś to potestować w zasięgu agregacji? Może pomimo tego, iż nie jest do 23a warto na niego przerzucić się?

[iSilverBullet]

SSH doesn't work on B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar

It gave me "access denied" when I entered the correct password

[iSilverBullet]

SSH doesn't work on B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar

It gave me "access denied" when I entered the correct password

update: I enabled telnet but I can't change IMEI with atc code, I get +CME ERROR: 2

[][No_WaY]

[quote="]
can you add it to the B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar so it will be complete exe or bin without any need to add shh command?[/quote]
And also can you please add loopback in bridge mode?
( Like in e5186 3heuigate bridge mode you need to attach 2 cable , one in lan/wan port number 4 to make bridge connection and pass the ip and other cable to any lan port 1-3 to make the loopback , this will let you connect the modem even if 4g connection is down because you can setup the router in same ip range due the presence of loopback , while in b525 situation there only one cable is needed that make ip pass through on any port but the problem that you lose the access to the router if 4g connection is down because there is no loopback!)

Can this be fixed?or extract bridge module from 3hueigate frim and incorporate it in b525 firm?

Thanks again

[garysek]

update: I enabled telnet but I can't change IMEI with atc code, I get +CME ERROR: 2

atc works correctly:

Kod: Zaznacz cały

130|root@p722:/ # atc ati

Manufacturer: Huawei Technologies Co.,Ltd.
Model: B525s-23a
Revision: 11.187.61.01.1133
IMEI: 861920035xxxxxx
+GCAP: +CGSM,+DS,+ES

OK
root@p722:/ #

I didn't need to change IMEI...


Faktycznie LTE CA działa nawet przy zerowym obciążeniu łącza:

[alcoo]

Klasyczne perpetuum mobile.

[iSilverBullet]

update: I enabled telnet but I can't change IMEI with atc code, I get +CME ERROR: 2

atc works correctly:

Kod: Zaznacz cały

130|root@p722:/ # atc ati

Manufacturer: Huawei Technologies Co.,Ltd.
Model: B525s-23a
Revision: 11.187.61.01.1133
IMEI: 861920035xxxxxx
+GCAP: +CGSM,+DS,+ES

OK
root@p722:/ #

I didn't need to change IMEI...


Faktycznie LTE CA działa nawet przy zerowym obciążeniu łącza:

atc is working but we still can't change the imei like we used to do on the modified Russian version (182)
Can you please make it possible with this update?

[][No_WaY]

1-can you add permanent telnet to the B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar so it will be complete exe or bin without any need to add shh command?
2- And also can you please add loopback in bridge mode?

( Like in e5186 3heuigate bridge mode you need to attach 2 cable , one in lan/wan port number 4 to make bridge connection and pass the ip and other cable to any lan port 1-3 to make the loopback , this will let you connect the modem even if 4g connection is down because you can setup the router in same ip range due the presence of loopback , while in b525 situation there only one cable is needed that make ip pass through on any port but the problem that you lose the access to the router if 4g connection is down because there is no loopback and ip router different ip range!)

Can this be fixed?or extract bridge module from 3hueigate frim and incorporate it in b525 firm?

Thanks again

[alcoo]

A czy ktoś zrobił/wymyślił nakładkę na rozbudowane statystyki do naszego routera? Tak żeby sumowal transfer danych w oby dwie strony dla ustalonego okresu rozliczeniowego.

Ten który jest obecnie jest taki okrojony i mało transparentny. Teraz wskazuje przesył danych w obie dwie strony?

[][No_WaY]

unfortunately after extensive testing for B525s-95a_UPDATE_11.187.61.01.1133_DBU.rar it not support CA , despite 4g+ sing the speed is only of one band!
on other hand
B525s-23a_UPDATE_11.182.61.00.778_DBU.rar
shows 4g+ only on increase demand and make real CA.

any idea or fix?