Huawei B525s-23a mod firmware.

[alcoo]

Przeczytaj mojego pierwszego posta w tym wątku i przestań pisać głupoty bo chyba nie warto. Widze, że sam nie ogarniasz wpisów. Zakończmy te dysputy. Spamujemy nie na temat.

[pepe_lodz]

Robertnik a czy dasz mi odp czy w tym sofcie jest już opcja BRIDGE MODE ?

[sebol2934]

Robertnik a czy dasz mi odp czy w tym sofcie jest już opcja BRIDGE MODE ?

Tak jest, linki zostały podane na poprzednich stronach.

[sebol2934]

Wszedłem zobaczyć czy ktoś odpisał na mój problem, no ale nic:( to chociaż wam może @alcoo i @robertnik pomogę dojść do porozumienia:)

Zaczęło się od pytań @krzysPN

Dzięki, jeszcze prosba o info:
1. Jaki max pojemnośc pendrive obsłuży ten router po przeróbce?
2. Czy ktoś przypadkiem odpalał na nim telefon analogowy z sieci plfon ??
3. Czy sa jakies przesłanki np. pogorszenie zasięgu czy cos innego o czy należy wiedzieć po zmianie (karta z sieci t-mobile) pytam bo któryś z użytkowników wyraził niezadowolenie że żałuje że zmienił
4. W związku z pkt 3 pytanie czy da się w razie czego wrócić do stanu pierwotnego?

na pytanie 3 i 4 odpowiedział @robertnik

Nikt nie robił testów, ale pare osób zauważyło że B525 ma problemy z 1800(na 4PDA użytkownik nie napisał czy przed flashem robił test, czy po), więc istnieje możliwość że to procedura ma na to destrukcyjny wpływ. W ilu % jest prawdziwa nikt się nie dowie puki nie sprawdzi przed i po niej, a najlepiej porówna 2 fizyczne egzemplarze z miodem i bez.
Jeśli to ona uszkadza sprzęt powrót na inne firmware nie pomaga, sprawdzałem już wiele.

Parafrazując robertnika, użytkownicy z forum 4pda.ru podnoszą kwestię, że zmiana oprogramowania może nieodwracalnie pogorszyć parametry sprzętu - w mojej opinii bzdura.

pozdro

[robertnik]

w mojej opinii bzdura.

Możliwe, nawet można to udowodnić, a nie bazować na opinii. Trzeba tylko porównać działanie na wymuszonych pasmach modowany B525 z innym ruterem, nawet nie koniecznie z B525.

[sebastan]

Ja działam na 1800 w T-M. Posiadam dwie karty, jedna w b525 modowanym, druga w Netgear 810S, Mam jeszcze w Note 8 i S8. Wydaje mi się, że na pewno B525 nie chodzi gorzej, Prędkości na nim widzę zblizone do innych sprzętów w tym samym czasie i lokalizacji. Pingi też, nieraz poniżej 20. Sprawdzić coś konkretnego?

[robertnik]

Pewnie speedtest na wymuszonych pasmach.

[garysek]

Niedawno kupiłem kolejnego B525 w T-mobile, a wczoraj nudziłem się to go rozkręciłem. Tym razem wrzuciłem do niego troszkę nowszy soft, ale połączyłem go ze sprawdzonym Webui:

11.182.61.00.778_DB
Zmiany względem 11.182.61.00.778:
- dodana obsługa ssh/scp (dropbear)
- dodany cron
- dodany program atc (do wykonywania komend AT)
- dodany serwer adb (ale nie jest automatycznie uruchamiany - można odpalić ręcznie z poziomu konsoli)
- scalony z webui Mod1.3pl

Mod1.3pl
Zmiany względem Mod1.2pl:
- w Bridge mode odblokowanie menu Ustawienia sieci

B525s-23a_UPDATE_11.182.61.00.778_DB.rar

Soft nie ma patch'a pozwalającego na wgrywanie z jego poziomu niepodpisanych softów i patcha ttl. Nie wiem, czemu Rosjanie tak go uwielbiają - u nas chyba nikomu do szczęścia nie potrzebny.
Cała reszta, łącznie z Bridge mode wydaje się działać jak należy.

[xyy333]

uwielbiaja patch TTL bo maja oferty na dane tylko na telefon, bez prawa do dalszego podziału łącza

[][No_WaY]

Niedawno kupiłem kolejnego B525 w T-mobile, a wczoraj nudziłem się to go rozkręciłem. Tym razem wrzuciłem do niego troszkę nowszy soft, ale połączyłem go ze sprawdzonym Webui:

11.182.61.00.778_DB
Zmiany względem 11.182.61.00.778:
- dodana obsługa ssh/scp (dropbear)
- dodany cron
- dodany program atc (do wykonywania komend AT)
- dodany serwer adb (ale nie jest automatycznie uruchamiany - można odpalić ręcznie z poziomu konsoli)
- scalony z webui Mod1.3pl

Mod1.3pl
Zmiany względem Mod1.2pl:
- w Bridge mode odblokowanie menu Ustawienia sieci

B525s-23a_UPDATE_11.182.61.00.778_DB.rar

Soft nie ma patch'a pozwalającego na wgrywanie z jego poziomu niepodpisanych softów i patcha ttl. Nie wiem, czemu Rosjanie tak go uwielbiają - u nas chyba nikomu do szczęścia nie potrzebny.
Cała reszta, łącznie z Bridge mode wydaje się działać jak należy.

this firmware have the bridge mode from B525s-23a_UPDATE_11.170.61.00.07_mod_beta3 and all features ?

[][No_WaY]

and what is the new feature more than B525s-23a_UPDATE_11.170.61.00.07_mod_beta3?

[garysek]

11.236.01.00.00 - old software, bridge mode doesn't work propably
11.170.61.00.07 - newer software, bridge mode OK
11.182.61.00.778 - the newest Huawei soft I have (I don't know what they changed, but Bridge mode - OK)

WEBUI:
original @rust3028 mod1.1:

Unlocked sections "USSD", "Contacts" and "SIM-menu" and subsection "VoIP".
Added the display of some parameters in the "Device information" section, organized their auto-update.
Unlocked access to various settings.
Unlocked the configuration of the PPTP VPN client.
Added a full selection of network type and range selection.
In the main menu added the item "?" to quickly jump to the "Device Information" section.
The default language is Russian.
Added the display of the operator name and network technology in the status bar.
Added the display of parameters in the tooltip of the signal level indicator.
Added upload / transfer rate display.
Added the display of numerical values ​​of PLMN and the names of the operators "Yota" and "Fly" in the list of found networks.
Added a system for managing the list of USSD-commands (the commands are stored in the file /data/userdata/ussd/ussd_cmd_list.xml).
I made the autocomplete field "Username" for the convenience of authorization.
The timeout for automatic "unlocking" of the web interface has increased to 20 minutes.
Corrected and added profiles for a number of Russian operators.
Added the ability to specify DNS servers in DHCP settings.
Added the ability to specify DNS servers in the profile settings.
Implemented the installation of an arbitrary IP address of the router.
Added the ability to assign an IP address to the MAC address.

and I added my modifications:

- added and set to default Polish language
- memorizing the PIN (is in 11.170.61.00.07_mod_beta3)
- set time zone to GMT+01:00 (Warsaw)
- displaying the operator name 26034 (Networks!) added
- changing the signal level icons on the main screen
- activating ipv6 support

- bridge mode activated

- in Bridge mode unblock the Network settings menu (is in 11.170.61.00.07_mod_beta3)

Firmware:

- ssh server added
- cron added
- added atc program (to execute AT commands)
- added adb server (but it is not automatically started - it can be launched manually from the console)

[Mek88]

Sorry for my english.... I have Huawei b525.... I Connect to VPN..... But i have a problem.... Some time the connection VPN go down (offline).... After the connection go offline.... The router Connect automatic in internet with the sim card lte connection..... I need the router stop the internet connection if the VPN is not connected.... Can you help me please.... Can i install a firmware to do this.... (before i have another router and it was installed OPENVPN... And it work fine)

[pepe_lodz]

11.236.01.00.00 - old software, bridge mode doesn't work propably
11.170.61.00.07 - newer software, bridge mode OK
11.182.61.00.778 - the newest Huawei soft I have (I don't know what they changed, but Bridge mode - OK)

WEBUI:
original @rust3028 mod1.1:

Unlocked sections "USSD", "Contacts" and "SIM-menu" and subsection "VoIP".
Added the display of some parameters in the "Device information" section, organized their auto-update.
Unlocked access to various settings.
Unlocked the configuration of the PPTP VPN client.
Added a full selection of network type and range selection.
In the main menu added the item "?" to quickly jump to the "Device Information" section.
The default language is Russian.
Added the display of the operator name and network technology in the status bar.
Added the display of parameters in the tooltip of the signal level indicator.
Added upload / transfer rate display.
Added the display of numerical values ​​of PLMN and the names of the operators "Yota" and "Fly" in the list of found networks.
Added a system for managing the list of USSD-commands (the commands are stored in the file /data/userdata/ussd/ussd_cmd_list.xml).
I made the autocomplete field "Username" for the convenience of authorization.
The timeout for automatic "unlocking" of the web interface has increased to 20 minutes.
Corrected and added profiles for a number of Russian operators.
Added the ability to specify DNS servers in DHCP settings.
Added the ability to specify DNS servers in the profile settings.
Implemented the installation of an arbitrary IP address of the router.
Added the ability to assign an IP address to the MAC address.

and I added my modifications:

- added and set to default Polish language
- memorizing the PIN (is in 11.170.61.00.07_mod_beta3)
- set time zone to GMT+01:00 (Warsaw)
- displaying the operator name 26034 (Networks!) added
- changing the signal level icons on the main screen
- activating ipv6 support

- bridge mode activated

- in Bridge mode unblock the Network settings menu (is in 11.170.61.00.07_mod_beta3)

Firmware:

- ssh server added
- cron added
- added atc program (to execute AT commands)
- added adb server (but it is not automatically started - it can be launched manually from the console)

Ok
Daj nam linka do tego softu z Twoimi zmianami.... te co wszystkie tu wymieniłeś w liście...

[garysek]

Naprawdę

Jak zaczniesz liczyć posty nad Twoim to dojdziesz do numeru 6 (właściwie przy numerze 4 mógłbyś się zatrzymać, ale to tylko cytat więc zastawmy go). W Tym moim poście jest jeden wiersz pokreślony (czyli po prostu link) - kliknij na nim...

Przepraszam, ale czy naprawdę to taki wielki problem poczytać o czym pisze się w danym temacie?

Sorry for my english.... I have Huawei b525.... I Connect to VPN..... But i have a problem.... Some time the connection VPN go down (offline).... After the connection go offline.... The router Connect automatic in internet with the sim card lte connection..... I need the router stop the internet connection if the VPN is not connected.... Can you help me please.... Can i install a firmware to do this.... (before i have another router and it was installed OPENVPN... And it work fine)

You can write a vpn checking script and run it in cron every minute, for example.
But personally, I would advise you to use openvpn on an openwrt/lede router...

[Mek88]

Naprawdę

Jak zaczniesz liczyć posty nad Twoim to dojdziesz do numeru 6 (właściwie przy numerze 4 mógłbyś się zatrzymać, ale to tylko cytat więc zastawmy go). W Tym moim poście jest jeden wiersz pokreślony (czyli po prostu link) - kliknij na nim...

Przepraszam, ale czy naprawdę to taki wielki problem poczytać o czym pisze się w danym temacie?

Sorry for my english.... I have Huawei b525.... I Connect to VPN..... But i have a problem.... Some time the connection VPN go down (offline).... After the connection go offline.... The router Connect automatic in internet with the sim card lte connection..... I need the router stop the internet connection if the VPN is not connected.... Can you help me please.... Can i install a firmware to do this.... (before i have another router and it was installed OPENVPN... And it work fine)

You can write a vpn checking script and run it in cron every minute, for example.
But personally, I would advise you to use openvpn on an openwrt/lede router...

Thank you so much for your reply... can you help me to write this scripts to do that please?.... Or
Can you tell me how can I Install Open VPN in my Huawei b525 router please.

[garysek]

Thank you so much for your reply... can you help me to write this scripts to do that please?....

I think that should be enough:

Kod: Zaznacz cały

#!/bin/sh

STATUS=`cat /tmp/vpn.status` 2> /dev/null
if (ifconfig | grep P-t-P > /dev/null); then
	if [ "$STATUS" != "UP" ]; then
		echo "UP" > /tmp/vpn.status
		echo 1 > /proc/sys/net/ipv4/ip_forward
	fi
else
	if [ "$STATUS" != "DOWN" ]; then
		echo "DOWN" > /tmp/vpn.status
		echo 0 > /proc/sys/net/ipv4/ip_forward
	fi
fi

All you need to do is give commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /etc/check_vpn.sh -r /B525/check_vpn.sh -P 18033 garysek.podlasie.pl
chmod 755 /etc/check_vpn.sh
echo "*/1 * * * * /system/etc/check_vpn.sh" >> /etc/crontabs/root
cron restart

Just remember that the script checks the vpn tunnel once per minute.

[][No_WaY]

11.236.01.00.00 - old software, bridge mode doesn't work propably
11.170.61.00.07 - newer software, bridge mode OK
11.182.61.00.778 - the newest Huawei soft I have (I don't know what they changed, but Bridge mode - OK)

WEBUI:
original @rust3028 mod1.1:

Unlocked sections "USSD", "Contacts" and "SIM-menu" and subsection "VoIP".
Added the display of some parameters in the "Device information" section, organized their auto-update.
Unlocked access to various settings.
Unlocked the configuration of the PPTP VPN client.
Added a full selection of network type and range selection.
In the main menu added the item "?" to quickly jump to the "Device Information" section.
The default language is Russian.
Added the display of the operator name and network technology in the status bar.
Added the display of parameters in the tooltip of the signal level indicator.
Added upload / transfer rate display.
Added the display of numerical values ​​of PLMN and the names of the operators "Yota" and "Fly" in the list of found networks.
Added a system for managing the list of USSD-commands (the commands are stored in the file /data/userdata/ussd/ussd_cmd_list.xml).
I made the autocomplete field "Username" for the convenience of authorization.
The timeout for automatic "unlocking" of the web interface has increased to 20 minutes.
Corrected and added profiles for a number of Russian operators.
Added the ability to specify DNS servers in DHCP settings.
Added the ability to specify DNS servers in the profile settings.
Implemented the installation of an arbitrary IP address of the router.
Added the ability to assign an IP address to the MAC address.

and I added my modifications:

- added and set to default Polish language
- memorizing the PIN (is in 11.170.61.00.07_mod_beta3)
- set time zone to GMT+01:00 (Warsaw)
- displaying the operator name 26034 (Networks!) added
- changing the signal level icons on the main screen
- activating ipv6 support

- bridge mode activated

- in Bridge mode unblock the Network settings menu (is in 11.170.61.00.07_mod_beta3)

Firmware:

- ssh server added
- cron added
- added atc program (to execute AT commands)
- added adb server (but it is not automatically started - it can be launched manually from the console)

hello,
is this newer or just custom?
http://update.hicloud.com:8180/TDS/data ... 01.673.BIN

[][No_WaY]

11.236.01.00.00 - old software, bridge mode doesn't work propably
11.170.61.00.07 - newer software, bridge mode OK
11.182.61.00.778 - the newest Huawei soft I have (I don't know what they changed, but Bridge mode - OK)

WEBUI:
original @rust3028 mod1.1:

Unlocked sections "USSD", "Contacts" and "SIM-menu" and subsection "VoIP".
Added the display of some parameters in the "Device information" section, organized their auto-update.
Unlocked access to various settings.
Unlocked the configuration of the PPTP VPN client.
Added a full selection of network type and range selection.
In the main menu added the item "?" to quickly jump to the "Device Information" section.
The default language is Russian.
Added the display of the operator name and network technology in the status bar.
Added the display of parameters in the tooltip of the signal level indicator.
Added upload / transfer rate display.
Added the display of numerical values ​​of PLMN and the names of the operators "Yota" and "Fly" in the list of found networks.
Added a system for managing the list of USSD-commands (the commands are stored in the file /data/userdata/ussd/ussd_cmd_list.xml).
I made the autocomplete field "Username" for the convenience of authorization.
The timeout for automatic "unlocking" of the web interface has increased to 20 minutes.
Corrected and added profiles for a number of Russian operators.
Added the ability to specify DNS servers in DHCP settings.
Added the ability to specify DNS servers in the profile settings.
Implemented the installation of an arbitrary IP address of the router.
Added the ability to assign an IP address to the MAC address.

and I added my modifications:

- added and set to default Polish language
- memorizing the PIN (is in 11.170.61.00.07_mod_beta3)
- set time zone to GMT+01:00 (Warsaw)
- displaying the operator name 26034 (Networks!) added
- changing the signal level icons on the main screen
- activating ipv6 support

- bridge mode activated

- in Bridge mode unblock the Network settings menu (is in 11.170.61.00.07_mod_beta3)

Firmware:

- ssh server added
- cron added
- added atc program (to execute AT commands)
- added adb server (but it is not automatically started - it can be launched manually from the console)

hello,

can you add B28(700nhz) to network setting?

with regards

[nilezon]

I just bought a B525s-23a.
Could someone please give me a very short instruction how to flash "B525s-23a_UPDATE_11.182.61.00.778_DB.exe" to get the bridge mode etc.
I don't understand much Russian or Polish, even with Google Translate :-(
Do I need to short the pins on the PCB? Then what? Any drivers needed?
Thank you

[nilezon]

I just bought a B525s-23a.
Could someone please give me a very short instruction how to flash "B525s-23a_UPDATE_11.182.61.00.778_DB.exe" to get the bridge mode etc.
I don't understand much Russian or Polish, even with Google Translate :-(
Do I need to short the pins on the PCB? Then what? Any drivers needed?
Thank you

Never mind. I successfully updated using the guide by @robertnik in first post. Google Translate to the rescue :-)
Thank you guys!

[garysek]

is this newer or just custom?
http://update.hicloud.com:8180/TDS/data ... 01.673.BIN

In my opinion custom.

can you add B28(700nhz) to network setting?

I can't test this, but try to enter these two commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /app/webroot/WebApp/common/js/mobilenetworksettings.js.gz -r /B525/mobilenetworksettings.js.gz -P 18033 garysek.podlasie.pl
wget -g -l /app/webroot/WebApp/common/html/mobilenetworksettings.html.gz -r /B525/mobilenetworksettings.html.gz -P 18033 garysek.podlasie.pl

[Mek88]

Thank you so much for your reply... can you help me to write this scripts to do that please?....

I think that should be enough:

Kod: Zaznacz cały

#!/bin/sh

STATUS=`cat /tmp/vpn.status` 2> /dev/null
if (ifconfig | grep P-t-P > /dev/null); then
	if [ "$STATUS" != "UP" ]; then
		echo "UP" > /tmp/vpn.status
		echo 1 > /proc/sys/net/ipv4/ip_forward
	fi
else
	if [ "$STATUS" != "DOWN" ]; then
		echo "DOWN" > /tmp/vpn.status
		echo 0 > /proc/sys/net/ipv4/ip_forward
	fi
fi

All you need to do is give commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /etc/check_vpn.sh -r /B525/check_vpn.sh -P 18033 garysek.podlasie.pl
chmod 755 /etc/check_vpn.sh
echo "*/1 * * * * /system/etc/check_vpn.sh" >> /etc/crontabs/root
cron restart

Just remember that the script checks the vpn tunnel once per minute.

Thank you Man for your help..... But where i have to plug in the script you have write?.... I have not find a menu on the router to write that code

[dzejk]

He said it clearly: "All you need to do is give commands in the ssh console".

[][No_WaY]

is this newer or just custom?
http://update.hicloud.com:8180/TDS/data ... 01.673.BIN

In my opinion custom.

can you add B28(700nhz) to network setting?

I can't test this, but try to enter these two commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /app/webroot/WebApp/common/js/mobilenetworksettings.js.gz -r /B525/mobilenetworksettings.js.gz -P 18033 garysek.podlasie.pl
wget -g -l /app/webroot/WebApp/common/html/mobilenetworksettings.html.gz -r /B525/mobilenetworksettings.html.gz -P 18033 garysek.podlasie.pl

what is the password for the ssh?

[Mek88]

He said it clearly: "All you need to do is give commands in the ssh console".

Before I have to install the modded firmware... And AFTER is possible to access in the ssh console? Is it correct?

[garysek]

@mek88, It obvious that we write about the modified software. SSH works on it only.

what is the password for the ssh?

Didn't you really try to connect without a password?
login: root
no pass

[Mek88]

@mek88, It obvious that we write about the modified software. SSH works on it only.

what is the password for the ssh?

Didn't you really try to connect without a password?
login: root
no pass

i have flash the firmware B525s-23a_UPDATE_11.182.61.00.778_DB ....
but i cant enter to the rooter ... what is the password and the login ??? i have try admin admin ... its not work

[][No_WaY]

@mek88, It obvious that we write about the modified software. SSH works on it only.

what is the password for the ssh?

Didn't you really try to connect without a password?
login: root
no pass

thanks

[][No_WaY]

is this newer or just custom?
http://update.hicloud.com:8180/TDS/data ... 01.673.BIN

In my opinion custom.

can you add B28(700nhz) to network setting?

I can't test this, but try to enter these two commands in the ssh console:

Kod: Zaznacz cały

wget -g -l /app/webroot/WebApp/common/js/mobilenetworksettings.js.gz -r /B525/mobilenetworksettings.js.gz -P 18033 garysek.podlasie.pl
wget -g -l /app/webroot/WebApp/common/html/mobilenetworksettings.html.gz -r /B525/mobilenetworksettings.html.gz -P 18033 garysek.podlasie.pl

what is the password for the ssh?

this is the result from ssh
login as: root
wget -g -l /app/webroot/WebApp/common/js/mobilenetworksettings.js.gz -r /B525/mobilenetworksettings.js.gz -P 18033 garysek.podlasie.pl <
Please check your Http URL garysek.podlasie.pl!
49|root@p722:/ # wget -g -l /app/webroot/WebApp/common/html/mobilenetworksettings.html.gz -r /B525/mobilenetworksettings.html.gz -P 18033 garysek.podlasie.pl
Please check your Http URL garysek.podlasie.pl!
49|root@p722:/ #


any comment?